Certain types of radial bearings can also take thrust load.

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

+1 vote

1 answer

A flange of radius 200mm is fastened to the machine screw by means of four cap screws of pitch circle radius 150mm. The external force P is 20kN which is loaded at 160mm from the machine screw. There are two dowel pins to take shear load. Determine the core diameter of cap screw if permissible tensile stress in cap screw is 40N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Which of the following statements are true about eccentrically loaded circular base?

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Which bolt is under maximum stress if dowel pins are used to relieve cap screws from shear stress?

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Determine the angle θ so that the force in the bolt 1 has maximum value.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

In angular contact bearings, ____ bearings are required to take thrust load in both directions.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Angular contact bearing can take thrust as well as radial loads.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Find the torque required to raise the load of 15kN and mean diameter of triple threaded screw being 46mm. Also given pitch=8mm and coefficient of friction is 0.15.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

The dynamic load carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

How many types of jacks are there which can be used in a screw jack?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the overall efficiency if nominal diameter=22mm and pitch=5mm.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

What is the output from differential screws when pitch of the two screws is 12mm and 8mm? Also the nut is rotated by applying a force of 120N at a radius of 300mm and the two screws remain stationary. The torque of raising and lowering for the two screws is 5k N-mm and 2.5k N-mm where k is the effective axial weight on the screw.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the clamping force W if nominal diameter=22mm and pitch=5mm.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Determine the secondary shear stress acting on the bolt 3 and its direction. The bolts are equidistant having separated by 60mm and the margin to the left and right is 25mm.Also P=5kN acts at a distance of 200mm from the channel.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the collar torque in terms of clamping force W assuming uniform wear theory if nominal diameter=22mm and pitch=5mm.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Find the ratio of the effective tensile load to which the two bolts are subjected.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The static load carrying capacity of fine threads is greater than that of coarse threads.

asked Jan 21 in Machine Design by Chris (48.2k points)

0 votes

0 answers

The shock absorbing capacity of bolts can be increased by

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Find the radius of Mohr circle which can be made from the shear stress and tensile stress acting on bolts.(Consider bolt under max stress and area of bolt is A)

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Which bolt can be used as criteria for designing?

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

The transverse shear stress at the root of the threads in the nut can be given by?(symbols have their usual meaning, z=number of threads in nut)

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Trapezoidal threads are better than square threads as there is radial pressure or side thrust on the nut.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Find the effective tensile force acting in the two bolts.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Determine the size of bolts using maximum shear stress theory.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Find the principal shear stress in the top bolts in terms of area A?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Arrange the bolts in order of decreasing shear stresses.

asked 3 days ago in Machine Design by Carter (86.7k points)

...