Due to slip of belt, the velocity ratio of the belt drive increases.

Question

Due to slip of belt, the velocity ratio of the belt drive increases.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

Due to slip of the belt, the velocity ratio of the belt drive

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Creep in belt drive is due to

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The ratio of driving tensions for rope drive is same as that of V-belt drive.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a multiple V- belt drive, when a single belt is damaged, it is preferable to change the complete set to

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a multiple V- belt drive, all the belts should stretch at the same rate.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a multiple V-belt drive, if one of the belt is broken, then we should replace

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The velocity of the belt for maximum power is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

When the belt is stationary, it is subjected to some tension known as initial tension. The value of this tension is equal to the

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

When two pulleys of different diameters are connected by means of an open belt, the angle of contact at the _________pulley must be taken into consideration.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The centrifugal tension on the belt has no effect on the power transmitted.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The power transmitted by a belt is maximum when the maximum tension in the belt is __________of centrifugal tension.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

If the velocity ratio for an open belt drive is 8 and the speed of driving pulley is 800 r.p.m, then considering an elastic creep of 2% the speed of the driven pulley is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The ratio of the driving tensions for V-belts is _____________ times that of flat belts.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The creep in a belt drive is due to the

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

V-belts are usually used for

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a cone pulley, if the sum of radii of the pulleys on the driving and driven shafts is constant, then

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The velocity ratio of two pulleys connected by an open belt or crossed belt is

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The chain drive transmits ____________ power as compared to belt drive.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The advantages of the V-belt drive over flat belt drive are

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Two pulleys of diameters d1 and d2 and at distance x apart are connected by means of an open belt drive. The length of the belt is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

If the angle of wrap on smaller pulley of diameter 250 mm is 120^0 and diameter of larger pulley is twice the diameter of smaller pulley, then the centre distance between the pulleys for an open belt drive is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

When two pulleys of different diameters are connected by means of an open belt drive, then the angle of contact taken into consideration should be of the

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The groove angle of the pulley for V-belt drive is usually

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The disadvantages of the V-belt drive over flat belt drive are

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In short open-belt drives, an idler pulley is used in order to decrease the angle of contact on the smaller pulley for higher power transmission.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

Greg · Answer 1 · 2022-10-20T07:03:16+0000

Right choice is (b) False

Explanation: The result of the belt slipping is to reduce the velocity ratio of the system.

Due to slip of belt, the velocity ratio of the belt drive increases.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories