The centrifugal tension in belts

Question

The centrifugal tension in belts

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

The power transmitted by a belt is maximum when the maximum tension in the belt is __________of centrifugal tension.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The centrifugal tension on the belt has no effect on the power transmitted.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a multiple V- belt drive, all the belts should stretch at the same rate.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The ratio of the driving tensions for V-belts is _____________ times that of flat belts.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

V-belts are usually used for

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The V-belts are particularly suitable for _____________ drives.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The power transmitted by a belt is maximum when the maximum tension in the belt (T) is equal to

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

When the belt is stationary, it is subjected to some tension, known as initial tension. The value of this tension is equal to the

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

When the belt is stationary, it is subjected to some tension known as initial tension. The value of this tension is equal to the

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In short open-belt drives, an idler pulley is used in order to decrease the angle of contact on the smaller pulley for higher power transmission.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A person weighing 600 N platform attached to the lower block of a system of 5 pulleys arranged in the second system. The platform and the lower block weigh 100N. The man himself supports by exerting a downward pull at the free end of the rope. Neglecting friction, the minimum pull of the man will be

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

For cutting multi-start threads, the speed ratio is expressed in terms of the lead of the job thread and lead of the lead screw threads.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Creep in belt drive is due to

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In the figure given below, what the quantity ‘p’ is known as _________

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a weston differential pulley block, the number of recesses in the smaller wheel is 9/10 of that of the larger wheel. If the efficiency of the machine is 50%, find the load lifted by an effort of 300N.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a multiple V-belt drive, if one of the belt is broken, then we should replace

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In order to have smooth operation, the minimum number of teeth on the smaller sprocket, for moderate speeds, should be

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The toothed wheels in chain drives are known as ______

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The chains are made up of rigid links which are hinged together in order to avoid flexibility for warping around the driving and driven wheels.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Five pulleys are arranged in the second system of pulleys. When not loadwd the effort required to raise the movable block is 35N. Further wastage in friction increases the pull at the rate of 3% of the load lifted. What is the efficiency of the system at 2kN?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a wheel and differential axle, the diameter of the effort wheel is 400 mm. The radii of the load axles are 150mm and 100 mm respectively. The diameter of the rope is 10 mm. Find the load which can be lifted by an effort of 100 N, assuming an efficiency of the machine to be 75%.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Five pulleys are arranged in the second system of pulleys. When not loaded the effort required to raise the movable block is 35N. Further wastage in friction increases the pull at the rate of 3% of the load lifted. What is the effort required to raise a load of 2kN?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The creep in a belt drive is due to the

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a cone pulley, if the sum of radii of the pulleys on the driving and driven shafts is constant, then

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a multiple V- belt drive, when a single belt is damaged, it is preferable to change the complete set to

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

Greg · Answer 1 · 2022-10-20T06:55:31+0000

The correct answer is (c) have no effect on the power transmitted

To elaborate: None.

The centrifugal tension in belts

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories