A single cylinder oil engine works with a three rotor system, the shaft length is 2.5m and 70mm in diameter, the middle rotor is at a distance 1.5m from one end. Calculate the free torsional vibration frequency for a single node system in Hz if the mass moment of inertia of rotors in Kg-m^2 are: 0.15, 0.3 and 0.09. C=84 kN/mm^2

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

A single cylinder oil engine works with a three rotor system, the shaft length is 2.5m and 70mm in diameter, the middle rotor is at a distance 1.5m from one end. Calculate the free torsional vibration frequency for a two node system in Hz if the mass moment of inertia of rotors in Kg-m^2 are: 0.15, 0.3 and 0.09. C=84 kN/mm^2

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a gearing system, pump speed is one third of the motor. Shaft from motor is 6 cm in diameter and 30cm long, the impellar shaft is 10cm diameter and 60cm long. Mass moment of inertia is 1500 Kg-m^2, C = 80Gn/m^2. Neglecting the inertia of shaft and gears calculate the frequency of free torsional vibrations in Hz.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

the given figure, considering left end has one rotor, If the mass moment of inertia of the shaft till node N1 is increased to four times, then what will be the effect on free torsional vibrations of a rotor at left end of N1?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m^2. Calculate the natural longitudinal frequency in Hz.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a vibration system having different shaft parameters, calculate which of the following cannot be the diameter of the equivalent shaft if the diameters of shafts in m are: 0.05, 0.06, 0.07.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Keeping the mass moment of inertia of left end and the right end shafts in a three rotor system same, if the length of one shaft is doubled what should be the effect on the length of other shaft?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The crank-pin circle radius of a horizontal engine is 300 mm. The mass of the reciprocating parts is 250 kg. When the crank has travelled 30° from T.D.C., the difference between the driving and the back pressures is 0.45 N/mm^2. The connecting rod length between centres is 1.2 m and the cylinder bore is 0.5 m. If the engine runs at 250 r.p.m. and if the effect of piston rod diameter is neglected, calculate the net load on piston.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A flywheel is mounted on a vertical shaft. The both ends of a shaft are fixed and its diameter is 50 mm. The flywheel has a mass of 500 kg, the modulus of rigidity for the shaft material is 80 GN/m^2 and its radius of gyration is 0.5 m. Find the natural frequency of torsional vibrations.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the given figure, considering PN as one shaft, If the mass moment of inertia is increased to four times, then what will be the effect on free torsional vibrations of a rotor at P?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a three rotor system, free torsional vibration cannot occur if there is only one node.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a three rotor system in the figure given below, the length of one shaft(P) is twice the other(Q), then what is the relation between the Mass moment of inertia of the shafts.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Free torsional vibrations will occur in a three rotor system only if all rotors have same frequency.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m^2. Determine the frequency of transverse vibrations of the shaft.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Keeping the mass moment of inertia of both the shafts in a two rotor system same, if the length of one shaft is doubled what should be the effect on the length of other shaft?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

What is the total number of nodes formed in a three rotor system if the rotors at one of the ends and the one in the middle rotate in the same direction?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a two rotor system, the mass moment of inertia of one shaft(A) is twice the other(B), then what is the relation between the length of the shafts.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a two rotor system, the length of one shaft(A) is twice the other(B), then what is the relation between the Mass moment of inertia of the shafts.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m^3. Determine the static deflection of the shaft in mm.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the mass moment of inertia is increased to four times, then what will be the effect on free torsional vibrations of a single motor system?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Free torsional vibrations will occur in a two rotor system only if both rotors have same frequency.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A uniform disc of diameter 300 mm and of mass 5 kg is mounted on one end of an arm of length 600 mm. The other end of the arm is free to rotate in a universal bearing. If the disc rotates about the arm with a speed of 300 r.p.m. clockwise, looking from the front, with what speed will it precess about the vertical axis?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In order to prepare Lithium nitride, air is passed gently over a reactor. Suppose that Nitrogen diffuse to a length 5cm before getting reacted with Lithium. Nitrogen reacts with lithium quickly so that partial pressure of Nitrogen at that point is 0. Reactor is a cylinder of length 10cm and diameter 2cm. Assume air to be a mixture of Nitrogen and Oxygen only. The temperature is 298K and total pressure 1atm. Diffusivity of N2 in O2 is 2*10^-5m^2/s. Calculate the Molar flux (mol/m^2.s) of N2 at a distance of 2.5cm from the top with respect to an observer moving with twice the mass average velocity a direction towards the liquid surface. (R=8.205*10^-5m^3atmK^-1mol^-1). Assume z=0 at the top of the reactor.

asked Sep 20, 2022 in Mass Transfer by Julian (38.2k points)

+1 vote

1 answer

If a mass whose moment of inertia is Ic/3 is placed at the free end and the constraint is assumed to be of negligible mass, then the kinetic energy is ______

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a two rotor system, torsional vibration occurs only if the rotors are moving in the same direction.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For occurrence of free torsional vibration in a three rotor system which of the condition is necessary?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

...