The first critical speed of an automobile running on a sinusoidal road is calculated by (modeling it as a single degree of freedom system)

Question

The first critical speed of an automobile running on a sinusoidal road is calculated by (modeling it as a single degree of freedom system)

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

The critical speed of a shaft with a disc supported in between is equal to the natural frequency of the system in

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Critical speed is expressed as

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The natural frequency of a spring-mass system on earth is ωn. The natural frequency of this system on the moon (gmoon = gearth/6) is

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

While calculating the natural frequency of a spring-mass system, the effect of the mass of the spring is accounted for by adding X times its value to the mass, where X is

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The accelerometer is used as a transducer to measure earthquake in Richter scale. Its design is based on the principle that

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In vibration isolation system, if ω/ωn, then the phase difference between the transmitted force and the disturbing force is

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In vibration isolation system, if ω/ωn < 2, then for all values of damping factor, the transmissibility will be

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When a body is subjected to transverse vibrations, the stress induced in a body will be

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In steady state forced vibrations, the amplitude of vibrations at resonance is _____________ damping coefficient.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The factor which affects the critical speed of a shaft is

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The combined mass of bicycle and rider is 100 kg, they are travelling at the speed of 16 km/h on a level road. Diameter of rear wheel is 0.9m. The pressure applied on the brake is 100 N and μ = 0.05., find the no. of revolutions made by the bicycle before it comes to rest.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The ratio of the actual damping coefficient (c) to the critical damping coefficient (cc ) is known as _________

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The speed at which the shaft runs so that the additional deflection from the axis of rotation of the shaft becomes infinite, is known as _________

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In under damped vibrating system, if x1 and x2 are the successive values of the amplitude on the same side of the mean position, then the logarithmic decrement is equal to

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Assuming the shaft to be freely supported. Calculate the whirling speed of the shaft : 2 cm diameter and 60 cm long carrying a mass of 1 kg at its mid-point. The density of the shaft material is 40 Mg/m^3, and Young’s modulus is 200 GN/m^2.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A cantilever shaft has a diameter of 6 cm and the length is 40cm, it has a disc of mass 125 kg at its free end. The Young’s modulus for the shaft material is 250 GN/m². Calculate the static deflection in nm.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The combined mass of bicycle and rider is 100 kg, they are travelling at the speed of 16 km/h on a level road. Diameter of rear wheel is 0.9m. How far will the bicycle travel after the application of brake? The pressure applied on the brake is 100 N and μ = 0.05.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In damped vibrations, the amplitude of the resulting vibration gradually reduces. This is due to the reason that an amount of energy is always dissipated to overcome the ________

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Which of the following methods will give an incorrect relation of the frequency for free vibration?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Maximum displacement due to forced vibration is dependent on deflection due to static force.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The ratio of the maximum displacement of the forced vibration to the deflection due to the static force, is known as

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Fluid resistance causes damping which is known as ______

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Consider two governors A and B running at the same speed. When this speed increases or decreases by a certain amount, the lift of the sleeve of governor A is greater than the lift of the sleeve of governor B. Which of the following statement is true for the above situation?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The resistance to the motion of the body is provided by ______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A disc spinning on its axis at 20 rad/s will undergo precession when a torque 100 N-m is applied about an axis normal to it at an angular speed, if mass moment of inertia of the disc is the 1 kg-m^2

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

Fred · Answer 1 · 2022-10-16T08:49:04+0000

Right choice is (a) Resonance

Explanation: Frequency of automobile and road are same.

The first critical speed of an automobile running on a sinusoidal road is calculated by (modeling it as a single degree of freedom system)

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories