The cross-section of the flywheel arms is usually

Question

The cross-section of the flywheel arms is usually

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

The tensile stress in the flywheel rim due to the centrifugal force acting on the rim is given by

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If E = Mean kinetic energy of the flywheel, CS = Coefficient of fluctuation of speed and Δ E = Maximum fluctuation of energy, then

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a turning moment diagram, the variations of energy above and below the mean resisting torque line is called

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The ratio of the maximum fluctuation of energy to the ……. is called coefficient of fluctuation of energy.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The maximum fluctuation of speed is the

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The coefficient of fluctuation of speed is the _________ of maximum fluctuation of speed and the mean speed.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Due to the centrifugal force acting on the rim, the flywheel arms will be subjected to

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In order to find the maximum bending moment on the arms, it is assumed as a

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A circular solid disc of uniform thickness 20 mm, radius 200 mm and mass 20 kg, is used as a flywheel. If it rotates at 600 rpm, the kinetic energy of the flywheel, in Joules is

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a multicylinder engine, the moment of inertia of a flywheel is 6500 kg-m^2, from the turning moment diagram, it is found that fluctuation of energy is 56000 N-m, if mean speed is 120 rpm, then find maximum speed.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When engine torque is more than mean resisting torque, then the flywheel _______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The flywheel of a steam engine has a mass moment of inertia of 2500 Kg-m^2. The starting torque of the steam engine is 1500 N-m and may be assumed constant, using this data find the angular acceleration of the flywheel in rad/s^2.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a certain engine having an average speed of 1200 rpm, a flywheel approximated as a solid disc, is required for keeping the fluctuation of speed within 2% about the average speed. The fluctuation of kinetic energy per cycle is found to be 2 kJ. What is the least possible mass of the flywheel if its diameter is not to exceed 1 m ?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In order to reduce the heavy weight of the flywheel which of the following mechanical component is used?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The speed of an engine varies from 210 rad/s to 190 rad/s. During the cycle the change in kinetic energy is found to be 400 Nm. The inertia of the flywheel in kg/m2 is

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a punching press, the requirement is to punch 40 mm diameter holes in a plate having a thickness of 15 mm. The rate at which the holes should be punched is 30 holes/min. Energy requirement is of 6 N-m per mm2 of sheared area. If the punching takes time 1/10 of a second and the speed of the flywheel varies from 160 to 140 rpm, determine the mass of the flywheel having radius of gyration of 1 m.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The main function of a flywheel is to cause variations in the speed of a shaft caused by torque fluctuations.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The balance energy required for punching is supplied by the flywheel by ________

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Maximum fluctuation of energy in a flywheel is equal to

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The moment of inertia of a flywheel is 6500 kg-m^2, from the turning moment diagram, it is found that fluctuation of energy is 56000 N-m, if mean speed is 120 rpm, then find maximum speed.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The moment of inertia of a flywheel is 6500 kg-m^2, from the turning moment diagram, it is found that fluctuation of energy is 56000 N-m, if mean speed is 120 rpm, find the minimum speed.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A flywheel is fitted to the crankshaft of an engine having W as the amount of indicated work per revolution and permissible limits of coefficient of fluctuation of energy and speed as CE and CS respectively. The kinetic energy of the flywheel is given by

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the rotating mass of a rim type flywheel is distributed on another rim type flywheel whose mean radius is half the mean radius of the former, then energy stored in the latter at the same speed will be

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When engine torque is less than mean resisting torque, then the flywheel _______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The flywheel of a machine having weight of 4500 N and radius of gyration of 2 m has cyclic fluctuation of speed from 125 r.p.m to 120 r.p.m. Assuming g = 10m/s^2, the maximum fluctuation of energy is

asked Sep 21, 2022 in Machine Dynamics by Grayson (34.3k points)

Fred · Answer 1 · 2022-10-14T00:49:18+0000

Right option is (a) elliptical

The best explanation: The cross-section of the arms is usually elliptical with major axis as twice the minor axis.

The cross-section of the flywheel arms is usually

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories