Taylor’s stability number is represented by the term __________

Question

Taylor’s stability number is represented by the term __________

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

The Taylor’s stability number is based on ___________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

For purely frictional soil, the Taylor’s stability number is ___________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

Which of the following quantity is called as Taylor’s stability number?

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

When the slope is fully submerged, which of the following has to be used for finding stability number?

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

The stability of a slope for a pure frictional soil, depends upon __________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

According to Taylor, the force causing instability in the sliding wedge is __________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

The factor of safety with respect to friction is __________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

The total cohesion force which resists the slipping along the slip arc at critical equilibrium is proportional to ___________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

A slope is to be constructed at an inclination of 30° with the horizontal. What will be the safe height of the slope at factor of safety of 1.5? The soil has the properties: c = 15 k N/m^2, φ=22.5° and γ = 19 k N/m^3.

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

What will be the factor of safety with respect to cohesion of a clay slope laid at 1 in 2 to a height of 10 m, if the angle of internal friction φ=10° ; c=25 k N/m^2 and γ = 19 k N/m^3?

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

In stability computation, the curve representing the real surface of sliding is usually replaced by ___________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

The area of U-diagram in finding stability of D/S slope during steady seepage, can be measured by ___________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

The stability of a finite slope can be investigated by which of the following method?

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

The pore water pressure at any point on the slip surface is represented by ____________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

Stability of slopes of an earth dam is tested under, which of the following condition?

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

In the limiting case of stability, the angle of slope is referred to as _____________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

Analysis of stability of slopes is used for determining ___________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

In the rectangular plot method if there are n-slices, the total number of ordinates will be ____________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

The rupture mass sliding down a surface in a definite pattern resembles __________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

Planar surface commonly occur in __________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

In Hilf’s equation ‘u = pa Δ / (va + hc γw – Δ)’, hc refers to __________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

The friction circle may be also referred as __________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

The factor of safety against safety is given by ________ equation.

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

The factor of safety with respect to cohesion is given by the equation ____________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

Factor of safety with respect to height is given by ______________ equation.

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

William · Answer 1 · 2022-02-09T19:14:22+0000

Correct answer is (b) Sn

Easiest explanation: Taylor’s stability is represented as Sn.

Taylor’s stability number is represented by the term __________

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories