How much spark per minute is required by an eight-cylinder engine running at 4000 rpm?

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

Which device is used to generate an electric current for producing spark in I.C. engine?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

What are the types of spark plug?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

The process of igniting fuel by heat of compression is called?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

If a driven pulley is made to rotate at 350 rpm by a driving pulley of 0.3 m diameter, running at 1400 rpm, what will be the length of open belt drive when the pulleys are 2 m apart?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

What percent of battery loss in 24 hours is known as battery leakage?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

Which device is used to control the quantity of oil circulation and to maintain correct pressure in the lubricating system?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

Which device is used for interrupting the low voltage primary current in the battery ignition?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

What is the name of the chemical solution used in a battery for chemical reactions?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

What should be the minimum specific gravity after which the electrolyte should be charged?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

While testing a wheat thresher at recommended throughout, 80 Nm torque is recorded at 750 rpm at the main shaft of the threshing cylinder, which is operated by a 200-mm diameter V pulley. The overload factor and unit mass of V-belt are 1.2 and 0.9 kg/m respectively. At condition of maximum power transfer the maximum tension in V-belt in N is ________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

A six-cylinder 4-stroke engine has bore diameter 11 cm and stroke length 12.2 cm running at 2800 rev/min consumes 455m^2 of air per hour. What would be the volumetric efficiency of the engine?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

In spark ignited engine the atomization of fuel takes place in ___________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A four-stroke diesel engine operating at 800 rpm uses 0.10 kg of fuel in 4 minutes while developing a torque of 70 Nm. Calculate brake specific fuel consumption

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A four cylinder two- stroke cycle engine with a swept volume of 750 cm^3 per cylinder gives a specific fuel consumption of 0.25 kg KW^-1 h^-1. When developing a brake mean effective mean pressure 650 kPa at 1500 rpm. What is the brake thermal efficiency, if the calorific value is 40 MJ kg^-1?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

In engine cylinder, the petrol is vaporised ____________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

An IC engine consumes high speed diesel oil at the rate of 0.5 kg/h. Calculate the power of the engine.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

How many hectares per day of 10 hours can be cut by a combine with 4 metre cutter bar, when it is running at 4 k/hr?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

Find the gear ratio of a tractor of its final drive of tractor has 1.2 m tractor wheel and forward speed of 5km/h. When engine is running at 1000 rpm if reduction in transmission is 3:1

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

In spark ignited engines, the fuel tank is placed ___________

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

What should be the gap of spark plug?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

A hydraulic circuit uses 25 litres of fluid per min. The fluid is supplied by a pump having a fixed displacement of 12.5 cm^3 per revolution driven at 3000 rpm. The pump has a volumetric efficiency of 0.85 and torque efficiency of 0.88. If the system pressure is set at 18 MPa by the relief valve. What will be the power required to drive the pump?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

What power is transmitted by belt and pulley arrangement, if tension on tight side of belt is 60 kg and tension on slack side is 25kg. The diameter and speed of driving pulley is 0.95 m and 250 rpm respectively.

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

Two pulleys are connected by a belt. The sum of the diameter of two pulleys is 90 cm and while one makes 50 rpm, the other makes 20 rpm. What will be the diameters of the other pulley?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

Two pulleys are connected by a belt. The sum of the diameter of two pulleys is 90 cm and while the one makes 50 rpm, the other makes 20 revolutions. What will be the diameter of the pulleys?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+2 votes

1 answer

A V-belt operates at 23.56 m/s peripheral speed. The mass of the belt per unit length is 0.9 kg/m. The value of centrifugal tension is _______

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

...