Wear ultimately results in ride in of the chain on sprocket teeth.

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

In roller chains, there is sliding friction between roller and sprocket teeth.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Chain drives suffer from wear problems.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The maximum achievable efficiency of the chain drives is about 80%.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Gear drives are preferred over chain drives for long centre distances.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A chain drive consist of an endless chain wrapped around two sprockets.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Chain drives require little or no maintenance and creates no noise.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

For non-parallel shafts, chain drives are highly recommended.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Belt drives have compact construction as compared to chain drives.

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The chain drive is same as gear drive.

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The driving sprocket has 19 teeth and rotates at 1100rpm. The pitch of the chain is 18mm. Calculate the velocity of the chain.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The designation ‘04B’ is as per ANSI series.

asked Jan 21 in Machine Design by Chris (52.6k points)

+1 vote

1 answer

If centre distance for a chain drive is 750mm with number of teeth on the driving and driven sprockets being 40 and 20 respectively, then calculate the number of links required. Given: Pitch is taken as 19mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The cross section of V belt consist of rubber backing to help engagement of teeth with sprocket.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Sum of number of links and number of teeth of the sprocket is _____

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Calculate the pitch circle diameter of the driving pulley is pitch is given as 18mm and sprocket has 19 teeth.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A plate clutch consists of 1 pair of contacting surfaces. The inner and outer diameter of the friction disk is 100mm and 200mm respectively. The coefficient of friction is 0.2 and permissible intensity of pressure is 1.5N/mm². Assuming uniform wear theory, calculate the operating force in the clutch.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A gear meshes with another gear and a sprocket meshes with another sprocket.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A plate clutch consists of 1 pair of contacting surfaces. The inner and outer diameter of the friction disk is 100mm and 200mm respectively. The coefficient of friction is 0.2 and permissible intensity of pressure is 1.5N/mm². Assuming uniform wear theory, calculate the power transmitting capacity of the clutch at 80rad/s.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

A cone clutch transmits 24kW at 490rpm. The coefficient of friction is 0.2 and allowable intensity of pressure is 0.35N/mm². The semi cone angle is 12⁰. The outer diameter is fixed as 310mm.Assuming uniform wear theory; find the face width of friction lining.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

For a new friction lining, uniform wear theory is used.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A cone clutch transmits 24kW at 490rpm. The coefficient of friction is 0.2 and allowable intensity of pressure is 0.35N/mm². The semi cone angle is 12⁰. The outer diameter is fixed as 310mm.Assuming uniform wear theory; find the inner diameter.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A plate clutch consists of 1 pair of contacting surfaces. The inner and outer diameter of the friction disk is 100mm and 200mm respectively. The coefficient of friction is 0.2 and permissible intensity of pressure is 1.5N/mm². Assuming uniform wear theory, calculate the torque transmitting capacity of the clutch.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A cone clutch transmits 24kW at 490rpm. The coefficient of friction is 0.2 and allowable intensity of pressure is 0.35N/mm². The semi cone angle is 12⁰. The outer diameter is fixed as 310mm.Assuming uniform wear theory; find the maximum torque which is transmitted.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The wear of band brake is even.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

When semi vertical angle is greater than angle of static friction, clutch results in self-engagement.

asked Jan 25 in Machine Design by Carter (89.5k points)

...