Entire torque is transmitted by friction in the clamp coupling.

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

+1 vote

1 answer

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm².

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m.

asked Jan 21 in Machine Design by Chris (52.6k points)

0 votes

0 answers

Determine the diameter of the bolts used in rigid flange coupling if transmitted torque is 270N-m, pitch circle diameter=125mm and four bolts are emplace in the coupling. Permissible shear stress in the bolts is 70N/mm².

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling.

asked Jan 21 in Machine Design by Chris (52.6k points)

0 votes

0 answers

Does shaft has to be shifted i axial direction to remove clamp coupling.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The hub is treated as a solid shaft while calculating torsional shear stress in the hub.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If shaft diameter is 30mm and number of pins emplaced are 6, then the diameter of the pin will be?

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key.

asked 1 day ago in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A machine started malfunctioning due to some issues with the coupling. The coupling emplaced in the machine was Oldham. The only coupling available in the workshop is Hooke’s coupling. So Oldham coupling can be replaced by Hooke’s coupling.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A coupling is a mechanical device that temporarily joins two rotating shafts to each other.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Oldham coupling i used to connect two shafts having intersecting axes.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Axle is frequently used in torque transmission.

asked Jan 21 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the torque supplied to the shaft.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

In distortion energy theorem, if a unit cube is subjected to biaxial stress, then S(yt) is given by which of the following?

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

While designing shaft on the basis of torsional rigidity, angle of twist is given by?

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Flexible shafts have ___ rigidity in torsion making them flexible.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

A sunk key fits in the keyway of the _____ only.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm². The diameter of shaft and width of key can be taken as 40mm and 10mm respectively.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The region of safety for biaxial stresses is of which shape in the case of maximum distortion energy theorem.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If allowable shear stress in the shaft is 70N/mm² and torsional and bending moments are M=1185000N-mm and m=330000N-mm, find the diameter of the shaft.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If bending moment on point B in horizontal plate is M and in vertical plane is m, then the net bending moment at point B is?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Solid shafts are used in epicyclic gearboxes.

asked Jan 22 in Machine Design by Carter (89.5k points)

...