Does shaft has to be shifted i axial direction to remove clamp coupling.

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm².

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m.

asked Jan 21 in Machine Design by Chris (52.6k points)

0 votes

0 answers

If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling.

asked Jan 21 in Machine Design by Chris (52.6k points)

0 votes

0 answers

Entire torque is transmitted by friction in the clamp coupling.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If shaft diameter is 30mm and number of pins emplaced are 6, then the diameter of the pin will be?

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Determine the diameter of the bolts used in rigid flange coupling if transmitted torque is 270N-m, pitch circle diameter=125mm and four bolts are emplace in the coupling. Permissible shear stress in the bolts is 70N/mm².

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The hub is treated as a solid shaft while calculating torsional shear stress in the hub.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Oldham coupling i used to connect two shafts having intersecting axes.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A machine started malfunctioning due to some issues with the coupling. The coupling emplaced in the machine was Oldham. The only coupling available in the workshop is Hooke’s coupling. So Oldham coupling can be replaced by Hooke’s coupling.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm². The diameter of shaft and width of key can be taken as 40mm and 10mm respectively.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A coupling is a mechanical device that temporarily joins two rotating shafts to each other.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the torque supplied to the shaft.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The stiffness of solid shaft is more than the stiffness of hollow shaft with same weight.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

While designing shaft on the basis of torsional rigidity, angle of twist is given by?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Solid shaft is costlier than hollow shaft of same weight.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The strength of hollow shaft is more than the strength of solid shaft of same weight.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If allowable shear stress in the shaft is 70N/mm² and torsional and bending moments are M=1185000N-mm and m=330000N-mm, find the diameter of the shaft.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The shaft is always stepped with ________ diameter at the middle portion and __________ diameter at the shaft ends.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

______ is used for a shaft that supports rotating elements like wheels, drums or rope sleaves.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Counter shaft is a secondary shaft.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm².

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Is it necessary for an axle to be ______ with respect to rotating element?

asked Jan 23 in Machine Design by Carter (89.5k points)

...