If velocity ratio is more than 3, then centre distance is given by 2D.

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

If velocity ratio is less than 3, then centre distance is given by D+.5d.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A shorter centre distance is always preferred in belt drives.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

The optimum velocity of the belt for maximum transmission is given by √P/6m.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Power transmitting capacity of V belts is more than that of flat belt.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If centre distance for a chain drive is 750mm with number of teeth on the driving and driven sprockets being 40 and 20 respectively, then calculate the number of links required. Given: Pitch is taken as 19mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Vertical drives are preferred over horizontal.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Fabric rubber belts are not widely used as they can’t be operated at high speeds.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The layer of a belt is generally called as

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

In horizontal belt, the loose side is generally kept on the bottom.

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the angle of wrap if diameter of the two pulleys are 550mm and 300mm. Also the centre distance is 2800mm.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the arc of contact if diameter of the two pulleys are 550mm and 300mm. Also the centre distance is 2800mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

In a centrifugal clutch, when the centrifugal force is slightly more than the spring force, shoe begins to move in a radially inward direction.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The efficiency of flat belt drive is 35%. If all the parameters are same and flat belt is replaced by V belt, than the efficiency of V belt will be?

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Velocity ratio in both flexible and rigid drive is constant.

asked 1 day ago in Machine Design by Carter (89.5k points)

0 votes

0 answers

Moment of normal force and frictional forces about the pivot axis are 640000N-mm and 250000N-mm respectively. If force acts at a distance of 190mm from the pivoted point, calculate the actuating force.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If number of contacting surfaces are 5, then number of disks required in multi disk clutch are?

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A solid cast iron disk of mass 1000kg is rotating at 350rpm. Diameter of the disk is 1m and time taken to come to stop the disk by brake is 1.6sec.Square of radius of gyration is 0.2. Calculate the average angular velocity during braking period.

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The pitch diameter of bigger pulley D in terms of small diameter d is given by

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Gear drives are preferred over chain drives for long centre distances.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The intensity of normal pressure between the friction lining and the brake drum at any point is proportional to square of the vertical distance from the pivot.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

When semi vertical angle is greater than angle of static friction, clutch results in self-engagement.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The driving sprocket has 19 teeth and rotates at 1100rpm. The pitch of the chain is 18mm. Calculate the velocity of the chain.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The belt tension is maximum when velocity of belt is 0.

asked Jan 21 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Calculate the pitch circle diameter of the driving pulley is pitch is given as 18mm and sprocket has 19 teeth.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pivoted double block brake has a drum radius of 280mm with two shoes subtending an angle of 100⁰. Maximum pressure intensity is 0.5N/mm². If the width of friction lining is 90mm, find the torque capacity f each shoe. Assume coefficient of friction as 0.2.

asked 1 day ago in Machine Design by Carter (89.5k points)

...