Power transmitting capacity of V belts is more than that of flat belt.

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

Fabric rubber belts are not widely used as they can’t be operated at high speeds.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The optimum velocity of the belt for maximum transmission is given by √P/6m.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

The layer of a belt is generally called as

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

In horizontal belt, the loose side is generally kept on the bottom.

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The efficiency of flat belt drive is 35%. If all the parameters are same and flat belt is replaced by V belt, than the efficiency of V belt will be?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If velocity ratio is less than 3, then centre distance is given by D+.5d.

asked 3 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If maximum tension in the belt is 900N and allowable belt load is 500N. Calculate the number of belts required to transmit power.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Vertical drives are preferred over horizontal.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A plate clutch consists of 1 pair of contacting surfaces. The inner and outer diameter of the friction disk is 100mm and 200mm respectively. The coefficient of friction is 0.2 and permissible intensity of pressure is 1.5N/mm². Assuming uniform wear theory, calculate the torque transmitting capacity of the clutch.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Disk brakes have low torque transmitting capacity in high volumes.

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The cross section of V belt consist of rubber backing to help engagement of teeth with sprocket.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

In a centrifugal clutch, when the centrifugal force is slightly more than the spring force, shoe begins to move in a radially inward direction.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Belt, chain and rope are called rigid drives.

asked 3 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Belt drives have compact construction as compared to chain drives.

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

The belt tension is maximum when velocity of belt is 0.

asked Jan 21 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If torque capacity of a block brake is 240N-m and radius of drum is 210mm with coefficient of friction 0.4.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A solid cast iron disk of mass 1000kg is rotating at 350rpm. Diameter of the disk is 1m and time taken to come to stop the disk by brake is 1.6sec.Square of radius of gyration is 0.2. Calculate the torque capacity of the brake.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Power is transmitted only by key and friction in the cone clutch.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

In positive contact clutches, power transmission is achieved by means of friction.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

When semi vertical angle is greater than angle of static friction, clutch results in self-engagement.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

In a block brake with short shoe, it is assumed that friction force and normal reaction are concentrated at the midpoint of the shoe.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A self-locking differential brake and back stop brakes is same thing.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A plate clutch consists of 1 pair of contacting surfaces. The inner and outer diameter of the friction disk is 100mm and 200mm respectively. The coefficient of friction is 0.2 and permissible intensity of pressure is 1.5N/mm². Assuming uniform wear theory, calculate the operating force in the clutch.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Internally expanding brakes never suffer the problem of self-locking.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Gear drives are preferred over chain drives for long centre distances.

asked 3 days ago in Machine Design by Carter (86.7k points)

...