Are the bolts 2 and 3 subjected to same magnitude of force?

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

Calculate the effective force in vector form to which rivet 2 is subjected. Bolts are separated by 100mm and force P=30kN.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Calculate the diameter of the rivets if permissible shear stress is 60N/mm². Bolts are separated by 100mm and force P=30kN.

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If secondary shear stress acting on any bolts is given by Cxr₁ where r₁ is the distance of bolt from CG, then find the value of C. Bolts are equidistant with spacing of 100mm. Force P=30kN.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Calculate the primary shear stress on each rivet if P=30kN and diameter of rivets is 15mm.

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Two steel rods connected by cotter joint are subjected to 50 kN load each. What is the minimum diameter required of the rods? (Given: Yielding Stress= 400N/mm² ; Factor of Safety=6)

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

In hot riveting the shank portion is subjected to compressive stress.

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m.

asked Jan 21 in Machine Design by Chris (48.2k points)

0 votes

0 answers

Calculate width of the band if permissible tensile stress is 80N/mm². Force P=15kN and diameter of the rivet can be taken as 9mm. Given thickness=3mm

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Which equations can be used to find the resisting force in the two welds?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Referring to figure 1, determine the required length of the weld joining two steel plates which are 10mm wide and 10mm thick. The permissible shear stress in the weld is 80N/mm²

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

With reference to figure 1, a plate, 75mm wide and 10mm thick, is joined with another plate as shown. The permissible tensile and shear stress in the welds are 50/mm² and 40N/mm². Determine the required length of each parallel fillet weld if length of transverse weld is 40mm.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Find the length of weld 2 required to with stand the load of 100kN. Permissible shear stress in weld is 70kN/mm².

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Find the ratio of the effective tensile load to which the two bolts are subjected.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Determine the secondary shear stress acting on the bolt 3 and its direction. The bolts are equidistant having separated by 60mm and the margin to the left and right is 25mm.Also P=5kN acts at a distance of 200mm from the channel.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The amount by which the two rods to be joined are drawn together is called as?

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm².

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate the bending stress in the welds if P=40kN, leg=4mm and e=400mm.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Calculate the moment of inertia about the axis parallel to welds and shift it to CG by considering thickness of welds t.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

The bracket welded to the vertical plate by means of two fillet welds. Calculate size of the welds if P=40kN, leg=4mm and e=400mm. Maximum permissible value of shear stress in the weld is 70N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Rails in the field are generally welded by using

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

The two plates are welded as shown in the figure 1. It is an example of

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Among punching and drilling, which is cheaper?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Calculate the diameter of the rivets by crushing consideration if permissible compression stress in rivets is 120N/mm², thickness of plate 3mm and P=15kN.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Among flat head and snap head rivet, which has the higher head height?

asked 5 days ago in Machine Design by Carter (86.7k points)

...