If the load itself begin to the screw and descend down, unless a restraining torque is applied then the condition is termed as

Question

If the load itself begin to the screw and descend down, unless a restraining torque is applied then the condition is termed as

← Prev Question Next Question →

1 Answer

Related questions

0 votes

0 answers

If nominal diameter of screw thread=50mm and pitch=10mm then the mean diameter of the screw thread will be?

asked Jan 21 in Machine Design by Chris (52.6k points)

0 votes

0 answers

A power screw is only used to convert rotary motion into linear motion and not for transmitting power.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A power screw has no problem of wear as there is very less amount of friction associated.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

V threads are highly recommended for fastening as well as power transmission purpose.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Trapezoidal threads are better than square threads as there is radial pressure or side thrust on the nut.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which of the following are true for buttress threads?

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Tr 40 x 14(P 7), here 14 indicates

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If friction angle is 30’ then the maximum efficiency of the screw is

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Maximum possible efficiency of a self-locking screw is

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the screw torque in terms of clamping force W if nominal diameter=22mm and pitch=5mm.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Efficiency of the screw depends upon helix angle but does not depend on friction angle.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Efficiency of screw depends upon lead of the screw.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Find the torque required to raise the load of 15kN and mean diameter of triple threaded screw being 46mm. Also given pitch=8mm and coefficient of friction is 0.15.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Clutch and coupling can be considered to be same.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

In trapezoidal threads, f (coefficient of friction) can be taken as

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Cold rolled components have higher strengths and hardness than hot rolled components.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the collar torque in terms of clamping force W assuming uniform wear theory if nominal diameter=22mm and pitch=5mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A flange of radius 200mm is fastened to the machine screw by means of four cap screws of pitch circle radius 150mm. The external force P is 20kN which is loaded at 160mm from the machine screw. There are two dowel pins to take shear load. Determine the core diameter of cap screw if permissible tensile stress in cap screw is 40N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Find the mean coil diameter of a helical compression sprig if a load of 1200N is applied on the spring. Spring index is 6, and wire diameter 7mm.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If bending stress in a screw is of magnitude 95N/mm² and torsional shear stress of magnitude 15N/mm², then what is the principal shear stress?

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

What is the output from differential screws when pitch of the two screws is 12mm and 8mm? Also the nut is rotated by applying a force of 120N at a radius of 300mm and the two screws remain stationary. The torque of raising and lowering for the two screws is 5k N-mm and 2.5k N-mm where k is the effective axial weight on the screw.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

What is the efficiency of differential screws when pitch of the two screws is 12mm and 8mm? The nut is rotated by applying a force of 120N at a radius of 300mm and the two screws remain stationary. The torque of raising and lowering for the two screws is 5k N-mm and 2.5k N-mm where k is the effective axial weight on the screw.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If for a curved beam of trapezoidal cross section, radius of neutral axis is 89.1816mm and radius of centroidal axis is 100mm, then find the bending stress at inner fibre whose radius is 50mm. Area of cross section of beam is 7200mm² and the beam is loaded with 100kN of load.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

All type of stresses vanishes after as soon as the applied load is removed.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pivoted double block brake has a drum radius of 280mm with two shoes subtending an angle of 100⁰. Maximum pressure intensity is 0.5N/mm². If the width of friction lining is 90mm, find the torque capacity f each shoe. Assume coefficient of friction as 0.2.

asked Feb 2 in Machine Design by Carter (89.5k points)

Chris · Answer 1 · 2026-02-02T14:19:43+0000

Appropriate answer is (b) Overhaulting

Breaking it down, I'd say: Overhaulting is the condition when load itsel begin to turn the screw.

If the load itself begin to the screw and descend down, unless a restraining torque is applied then the condition is termed as

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories