A power screw has no problem of wear as there is very less amount of friction associated.

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

A power screw is only used to convert rotary motion into linear motion and not for transmitting power.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If the load itself begin to the screw and descend down, unless a restraining torque is applied then the condition is termed as

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Trapezoidal threads are better than square threads as there is radial pressure or side thrust on the nut.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

V threads are highly recommended for fastening as well as power transmission purpose.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If nominal diameter of screw thread=50mm and pitch=10mm then the mean diameter of the screw thread will be?

asked Jan 21 in Machine Design by Chris (48.2k points)

+1 vote

1 answer

Tr 40 x 14(P 7), here 14 indicates

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Efficiency of the screw depends upon helix angle but does not depend on friction angle.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If friction angle is 30’ then the maximum efficiency of the screw is

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

In trapezoidal threads, f (coefficient of friction) can be taken as

asked 5 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Maximum possible efficiency of a self-locking screw is

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Efficiency of screw depends upon lead of the screw.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Sliding contact bearings, also called plain bearings have no problem of wear.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the collar torque in terms of clamping force W assuming uniform wear theory if nominal diameter=22mm and pitch=5mm.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Cold rolled components have higher strengths and hardness than hot rolled components.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Clutch and coupling can be considered to be same.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A cone clutch transmits 24kW at 490rpm. The coefficient of friction is 0.2 and allowable intensity of pressure is 0.35N/mm². The semi cone angle is 12⁰. The outer diameter is fixed as 310mm.Assuming uniform wear theory; find the face width of friction lining.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A cone clutch transmits 24kW at 490rpm. The coefficient of friction is 0.2 and allowable intensity of pressure is 0.35N/mm². The semi cone angle is 12⁰. The outer diameter is fixed as 310mm.Assuming uniform wear theory; find the inner diameter.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A cone clutch transmits 24kW at 490rpm. The coefficient of friction is 0.2 and allowable intensity of pressure is 0.35N/mm². The semi cone angle is 12⁰. The outer diameter is fixed as 310mm.Assuming uniform wear theory; find the maximum torque which is transmitted.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Calculate the wear strength for a pair of bevel gears having face width=20mm, module=5mm, No of teeth on pinion and gear 25 and 40 respectively and PCD of pinion=75mm.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A plate clutch consists of 1 pair of contacting surfaces. The inner and outer diameter of the friction disk is 100mm and 200mm respectively. The coefficient of friction is 0.2 and permissible intensity of pressure is 1.5N/mm². Assuming uniform wear theory, calculate the operating force in the clutch.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

For a new friction lining, uniform wear theory is used.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A plate clutch consists of 1 pair of contacting surfaces. The inner and outer diameter of the friction disk is 100mm and 200mm respectively. The coefficient of friction is 0.2 and permissible intensity of pressure is 1.5N/mm². Assuming uniform wear theory, calculate the torque transmitting capacity of the clutch.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

How many types of jacks are there which can be used in a screw jack?

asked 3 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

A flange of radius 200mm is fastened to the machine screw by means of four cap screws of pitch circle radius 150mm. The external force P is 20kN which is loaded at 160mm from the machine screw. There are two dowel pins to take shear load. Determine the core diameter of cap screw if permissible tensile stress in cap screw is 40N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Efficiency of conventional power screw is greater than the efficiency of recirculating ball screw.

asked Jan 23 in Machine Design by Carter (86.7k points)

...