If friction angle is 30’ then the maximum efficiency of the screw is

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

Efficiency of the screw depends upon helix angle but does not depend on friction angle.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Maximum possible efficiency of a self-locking screw is

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Efficiency of screw depends upon lead of the screw.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

In trapezoidal threads, f (coefficient of friction) can be taken as

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Cold rolled components have higher strengths and hardness than hot rolled components.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Clutch and coupling can be considered to be same.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If the load itself begin to the screw and descend down, unless a restraining torque is applied then the condition is termed as

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If nominal diameter of screw thread=50mm and pitch=10mm then the mean diameter of the screw thread will be?

asked Jan 21 in Machine Design by Chris (52.6k points)

0 votes

0 answers

A power screw has no problem of wear as there is very less amount of friction associated.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A power screw is only used to convert rotary motion into linear motion and not for transmitting power.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If α denotes the lead angle and φ, the angle of friction, then the efficiency of the screw is written as

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

0 votes

0 answers

A pivoted double block brake has a drum radius of 280mm with two shoes subtending an angle of 100⁰. Maximum pressure intensity is 0.5N/mm². If the width of friction lining is 90mm, find the torque capacity f each shoe. Assume coefficient of friction as 0.2.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If for a trapezoidal thread, angle of thread is 15’ then what will be the replacement of the coefficient of friction which is 0.15.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which of the following are true for buttress threads?

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

V threads are highly recommended for fastening as well as power transmission purpose.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Trapezoidal threads are better than square threads as there is radial pressure or side thrust on the nut.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Tr 40 x 14(P 7), here 14 indicates

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the screw torque in terms of clamping force W if nominal diameter=22mm and pitch=5mm.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

For a double threaded screw, what will be the tangent of helix angle if nominal diameter and pitch are 100mm and 12mm respectively?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A cone clutch transmits 24kW at 490rpm. The coefficient of friction is 0.2 and allowable intensity of pressure is 0.35N/mm². The semi cone angle is 12⁰. The outer diameter is fixed as 310mm.Assuming uniform wear theory; find the maximum torque which is transmitted.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If bending stress in a screw is of magnitude 95N/mm² and torsional shear stress of magnitude 15N/mm², then what is the principal shear stress?

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the overall efficiency if nominal diameter=22mm and pitch=5mm.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Efficiency of conventional power screw is greater than the efficiency of recirculating ball screw.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

What is the efficiency of differential screws when pitch of the two screws is 12mm and 8mm? The nut is rotated by applying a force of 120N at a radius of 300mm and the two screws remain stationary. The torque of raising and lowering for the two screws is 5k N-mm and 2.5k N-mm where k is the effective axial weight on the screw.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If worm helix angle is 30⁰, then worm should have at least ___ threads.

asked Jan 23 in Machine Design by Carter (89.5k points)

...