How many modes are there for crack propagation?

Question

How many modes are there for crack propagation?

← Prev Question Next Question →

1 Answer

Related questions

0 votes

0 answers

The critical value at which crack extension occurs is called

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Stress intensity factor is the critical value of stress at which crack extension occurs.

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm².Considering only bending stress.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

A curved beam with eccentricity 0.02D is loaded with 1kN.Centroidal radius=4D and inner and outer radii are 3.5D and 4.5D respectively. Area of cross section is 0.8D². Find the dimension D if allowable stress is 110N/mm² and considering only direct tensile stress.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If for a curved beam of trapezoidal cross section, radius of neutral axis is 89.1816mm and radius of centroidal axis is 100mm, then find the bending stress at inner fibre whose radius is 50mm. Area of cross section of beam is 7200mm² and the beam is loaded with 100kN of load.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A curved beam has neutral axis is curved while loaded and straight when unloaded.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

All type of stresses vanishes after as soon as the applied load is removed.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

How many classes of levers are there?

asked 3 days ago in Machine Design by Carter (86.7k points)

+1 vote

1 answer

If there are residual stresses in the material, than lower factor of safety is used.

asked Jan 23 in Machine Design by Carter (86.7k points)

0 votes

0 answers

For cast iron components, which of the following strength are considered to be the failure criterion?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

How many types of jacks are there which can be used in a screw jack?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

How many grades of tolerances are there according to BIS system fits and tolerances?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Which of the following are important parts of knuckle joint?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If any cross section is subjected to direct tensile stress and bending stress, then find the dimension of cross section. Given length & breadth are t and 2t respectively. F=25kN acts on the top fibre of the cross section, M=F x t . Also maximum allowable tensile stress =100N/mm².

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

The distance between fulcrum and dead weights is 100mm. Dead weights are of 2945.2N. An effort of 294.52N acts on the other hand. Find the distance between the fulcrum and other end of the lever.

asked Jan 22 in Machine Design by Carter (86.7k points)

0 votes

0 answers

Maximum Principal Stress Theory is not good for brittle materials.

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

The total strain energy for a unit cube subjected to three principal stresses is given by?

asked Jan 23 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

For components made of ductile materials like steel, subjected to static loading which of the following strength is used as a failure of criterion?

asked Jan 22 in Machine Design by Carter (86.7k points)

+1 vote

1 answer

Modulus of rigidity for carbon steels is greater than that of grey cast iron.

asked Jan 21 in Machine Design by Carter (86.7k points)

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 20N/mm²Find the maximum amount of shear stress to which the body is subjected.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

According to principal stress theory, which option represents the correct relation between yield strength in shear (YSS) and the yield strength in tension (YST)?

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Type of load affects factor of safety.

asked 3 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

If a body is subjected to stresses in xy plane with stresses of 60N/mm² and 80N/mm² acting along x and y axes respectively. Also the shear stress acting is 20N/mm². Find the minimum normal stress.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

A right angled bell-crank is designed to raise a load of 5kN at short arm whose length is 100mm. Longer arm is of length 500mm. Calculate the reaction or force acting on the fulcrum.

asked 5 days ago in Machine Design by Carter (86.7k points)

0 votes

0 answers

Which of the following relationship is true? (p=Poisson’s ratio)

asked 5 days ago in Machine Design by Carter (86.7k points)

Chris · Answer 1 · 2026-01-27T10:57:40+0000

The suitable answer is (b) 3

Explanation: Opening, sliding and tearing are the 3 modes.

How many modes are there for crack propagation?

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories