The tooth profile most commonly used in gear drives for power transmission is

Question

The tooth profile most commonly used in gear drives for power transmission is

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

Gears with involute tooth profile transmit constant velocity ratios between shafts connected by them.

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A fixed gear having 100 teeth meshes with another gear having 25 teeth, the centre lines of both the gears being joined by an arm so as to form an epicyclic gear train. The number of rotations made by the smaller gear for one rotation of the arm is

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Speed reduction in a gear box is achieved using a worm and worm wheel. The worm wheel has 30 teeth and a pitch diameter of 210 mm. If the pressure angle of the worm is 20^o, what is the axial pitch of the worm?

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Spiral bevel gears designed to be used with an offset in their shafts are called ‘hypoid gears’

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

There are six gears A, B, C, D, E, F in a compound train. The numbers of teeth in the gears are 20, 60, 30, 80, 25 and 75 respectively. The ratio of the angular speeds of the driven (F) to the driver (A) of the drive is

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A pair of helical gears has fewer teeth in contact as compared to an equivalent pair of spur gears.

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In the case of spur gears, the mating teeth execute pure rolling motion with respect to each other from the commencement of engagement to its termination.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A speed reducer unit consists of a double-threaded worm of pitch = 11 mm and a worm wheel of pitch diameter = 84 mm. The ratio of the output torque to the input to rque is

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A pair of gears forms a rolling pair.

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In short open-belt drives, an idler pulley is used in order to decrease the angle of contact on the smaller pulley for higher power transmission.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The mathematical form of the bevel tooth profile which closely resembles a spherical involute but is fundamentally different is

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The angle between a tooth profile and a radial line at its pitch point is known as

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Lewis equation for design of involute gear tooth predicts the dynamic load capacity of a cantilever beam of uniform strength.

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Twenty degree full depth involute profiled 19-tooth pinion and 37-tooth gear are in mesh. If the module is 5 mm, the centre distance between the gear pair will be

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Tooth interference in an external in volute spur gear pair can be reduced by

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Pitch cone angle of pinion of straight tooth bevel gear pair with ratio 1.732 is

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The phenomenon when the tip of tooth undercuts the root on its mating gear is known as _______

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The form factor of a spur gear tooth depends upon

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which gear train is used for higher velocity ratios in a small space?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following is a commonly used pressure angle in gears?

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The diameter and plane of rotation surface or shaft centre which is used for locating the gear blank during fabrication of the gear teeth is known as

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

An electric motor drives a machine through a speed reducing gear of ratio 9:1. The motor armature, with its shaft and gear wheel, has moment of inertia 0.6 kg-m^2. The rotating part of the driven machine has moment of inertia 45 kg-m^2. The driven machine has resisting torque of 100 N-m and the efficiency of reduction gear is 95%. Find the power which the motor must develop to drive the machine at a uniform speed of 160 r.p.m.

asked Sep 23, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The worm gears are widely used for transmitting power at ______________ velocity ratios between non-intersecting shafts.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a clock mechanism, the gear train used to connect minute hand to hour hand, is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which type of gear train is used in clock mechanism to join hour hand and minute hand?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

Greg · Answer 1 · 2022-10-21T15:26:10+0000

Correct option is (b) An involute

The explanation is: It is due to easy manufacturing.

The tooth profile most commonly used in gear drives for power transmission is

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories