Industrial rotors will not have uniform diameter throughout their lengths.

Question

Industrial rotors will not have uniform diameter throughout their lengths.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

In order to have smooth operation, the minimum number of teeth on the smaller sprocket, for moderate speeds, should be

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The relation between the pitch of the chain (p) and pitch circle diameter of the sprocket (D) is given by

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

For cutting multi-start threads, the speed ratio is expressed in terms of the lead of the job thread and lead of the lead screw threads.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The chain drive transmits ____________ power as compared to belt drive.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which one of the following is a positive drive?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The advantages of the V-belt drive over flat belt drive are

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The speed of the sprocket reduces as the chain pitch _____________ for a given number of teeth.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The disadvantages of the V-belt drive over flat belt drive are

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The distance between the hinge centre of a link and the corresponding hinge centre of the adjacent link is called

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The diameter of the circle on which the hinge centres of the chain lie is known as _______

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

If the angle of wrap on smaller pulley of diameter 250 mm is 120^0 and diameter of larger pulley is twice the diameter of smaller pulley, then the centre distance between the pulleys for an open belt drive is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a wheel and differential axle, the diameter of the effort wheel is 400 mm. The radii of the load axles are 150mm and 100 mm respectively. The diameter of the rope is 10 mm. Find the load which can be lifted by an effort of 100 N, assuming an efficiency of the machine to be 75%.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A person weighing 600 N platform attached to the lower block of a system of 5 pulleys arranged in the second system. The platform and the lower block weigh 100N. The man himself supports by exerting a downward pull at the free end of the rope. Neglecting friction, the minimum pull of the man will be

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Five pulleys are arranged in the second system of pulleys. When not loadwd the effort required to raise the movable block is 35N. Further wastage in friction increases the pull at the rate of 3% of the load lifted. What is the efficiency of the system at 2kN?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Five pulleys are arranged in the second system of pulleys. When not loaded the effort required to raise the movable block is 35N. Further wastage in friction increases the pull at the rate of 3% of the load lifted. What is the effort required to raise a load of 2kN?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In short open-belt drives, an idler pulley is used in order to decrease the angle of contact on the smaller pulley for higher power transmission.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The wire ropes make contact at

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Creep in belt drive is due to

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In the figure given below, what the quantity ‘p’ is known as _________

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

When the belt is stationary, it is subjected to some tension, known as initial tension. The value of this tension is equal to the

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a weston differential pulley block, the number of recesses in the smaller wheel is 9/10 of that of the larger wheel. If the efficiency of the machine is 50%, find the load lifted by an effort of 300N.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following chains fall under the category of hoisting and hauling chains?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

When the belt is stationary, it is subjected to some tension known as initial tension. The value of this tension is equal to the

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a multiple V- belt drive, all the belts should stretch at the same rate.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a multiple V-belt drive, if one of the belt is broken, then we should replace

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

Greg · Answer 1 · 2022-10-20T15:29:45+0000

Right answer is (a) True

Easiest explanation: Industrial rotors are not uniform, because of fitment of pulleys, gears, belt etc.

Industrial rotors will not have uniform diameter throughout their lengths.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories