The maximum efficiency of square threaded power depends upon

Question

The maximum efficiency of square threaded power depends upon

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

For over hauling screw

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

For self locking screw

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following screw thread is used for lead screw of lathe?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following screw thread is adaptable to split type nut?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following screw thread is used for jacks, vices and clamps?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A cup is provided in screw jack

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following screw thread is used for transmitting force in one direction?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following screw thread is stronger than other threads?

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The force of friction does not depends upon the roughness of the surfaces.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The force of friction depends upon the material of which the contact surfaces are made.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The maximum efficiency of a screw jack is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The efficiency of a screw jack is maximum, when

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A single plate clutch, with both sides effective, has outer and inner diameters 300 mm and 200 mm respectively. The maximum intensity of pressure at any point in the contact surface is not to exceed 0.1 N/mm^2. If the coefficient of friction is 0.3, determine the power transmitted by a clutch at a speed 2500 r.p.m.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A screw jack has square threads and the lead angle of the thread is α. The screw jack will be self locking when the coefficient of friction (μ) is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The frictional torque for square thread at the mean radius r while raising load W is given by

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

If α denotes the lead angle and φ, the angle of friction, then the efficiency of the screw is written as

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The efficiency of a screw jack is given by

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A screw is said to be over hauling screw, if its efficiency is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Efficiency of a screw jack is given by

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A screw is said to be self locking screw, if its efficiency is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The power from the engine to the rear axle of an automobile is transmitted by means of

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following screw thread is adopted for power transmission in either direction?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Screws used for power transmission should have

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A multiple disc clutch has five plates having four pairs of active friction surfaces. If the intensity of pressure is not to exceed 0.127 N/mm^2, find the power transmitted at 500 r.p.m. The outer and inner radii of friction surfaces are 125 mm and 75 mm respectively. Assume uniform wear and take coefficient of friction = 0.3.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A 60 mm diameter shaft running in a bearing carries a load of 2000 N. If the coefficient of friction between the shaft and bearing is 0.03, find the power transmitted when it runs at 1440 r.p.m.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

Greg · Answer 1 · 2022-10-19T23:04:03+0000

Correct answer is (b) friction angle

Explanation: The efficiency of a square threaded screw depends upon the helix angle α and the friction angle φ.

The maximum efficiency of square threaded power depends upon

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories