When two links are connected by a pin joint, their instantaneous centre lies

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

The two links are said to have a pure rolling contact, when their instantaneous centre __________ on their point of contact.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

When a slider moves on a fixed link having curved surface, their instantaneous centre lies

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

When a slider moves on a fixed link having ____________ their instantaneous center lies at infinity.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A slider moving on a fixed link having constant radius of curvature will have its instantaneous centre at the center of the circle.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

According to Kennedy’s theorem, if three bodies move relatively to each other, their instantaneous centres will lie on

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The two links OA and OB are connected by a pin joint at O. If the link OA turns with angular velocity ω1 rad/s in the clockwise direction and the link OB turns with angular velocity ω2 rad/s in the anti-clockwise direction, then the rubbing velocity at the pin joint O is

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a mechanism, the fixed instantaneous centres are those centres which

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The instantaneous centres, which moves as the mechanism moves but joints are of permanent nature, are called permanent instantaneous centres.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The instantaneous centres which vary with the configuration of mechanism, are called

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following property of the instantaneous center is correct?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

If n links are connected at the same joint, the joint is equivalent to

asked Sep 23, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The magnitude of velocities of the points on a rigid link is

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A mechanism has 8 links, out of which 5 are binary, 2 are ternary and 1 is quaternary. The number of instantaneous centres of rotation will be

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a four bar linkage, s denotes the shortest link length, L is the longest link length, P and Q are the lengths of other two links. At least one of the three moving links will rotate by 360° if

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a 4 – bar linkage, if the lengths of shortest, longest and the other two links are denoted by s, l, p and q, then it would result in Grashof’s linkage provided that

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A helical coil spring of stiffness k is cut to two equal halves and then these are connected in parallel to support a vibrating mass m. The angular frequency of vibration, ωn is

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The magnitude of velocities of the points on a rigid link is directly proportional to the distances from the points to the instantaneous centre.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The angle between the axes of two shafts connected by Hooke’s joint is 18°. Determine the angle turned through by the driving shaft when the velocity ratio is maximum.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The velocity of the instantaneous centre relative to any third rigid link will be different.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Two shafts having an included angle of 150° are connected by a Hooke’s joint. The driving shaft runs at a uniform speed of 1500 r.p.m. The driven shaft carries a flywheel of mass 12 kg and 100 mm radius of gyration. Using the above data, calculate the maximum angular acceleration of the driven shaft in rad/s^2.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Two shafts having an included angle of 150° are connected by a Hooke’s joint. The driving shaft runs at a uniform speed of 1500 r.p.m. The driven shaft carries a flywheel of mass 12 kg and 100 mm radius of gyration. Using the above data, calculate the maximum torque required in N-m.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Two shafts with an included angle of 160° are connected by a Hooke’s joint. The driving shaft runs at a uniform speed of 1500 r.p.m. The driven shaft carries a flywheel of mass 12 kg and 100 mm radius of gyration. Find the maximum angular acceleration of the driven shaft.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A fixed gear having 200 teeth is in mesh with another gear having 50 teeth. The two gears are connected by an arm. The number of turns made by the smaller gear for one revolution of arm about the centre of bigger gear is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

When the pin connects one sliding member and the other turning member, the angular velocity of the sliding member is __________

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In the above question, if both the links OA and OB turns in clockwise direction, then the rubbing velocity at the pin joint O is

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

...