__________ is used to resist the end thrust of the shafts.

Question

__________ is used to resist the end thrust of the shafts.

1 Answer

Related questions

+1 vote

1 answer

When effect of friction is negligible, the force is transmitted by the link from driver to the driven link through the centre line of the pins connecting the link. With friction, the line of action shifts and is tangent to _____________

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

When the load on the rubbing surfaces is carried partly by a fluid viscous film and partly by areas of boundary lubrication, it is known as

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

When the lubrication is arranged so that rubbing surfaces are separated by a fluid film, and the load on the surfaces is carried entirely by the hydrostatic or hydrodynamic pressure in the film, it is known as

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

When the two solid surfaces sliding over each other are free from contaminating fluid or film, the resistance encountered is called

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

When the rubbing surfaces are separated from each other by a very thin film of lubricant it is known as

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Sliver sulphate, tungsten disulphide, graphite, molybdenum disulphide, lead oxide are examples of

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

For very low velocities of rotation, high loads, and with good lubrication can be taken as

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

For design of ordinary machinery, value of journal friction can be taken as

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following statements is not correct? (a)Hooke’s joint is used to connect two rotating co-planar, non-intersecting shafts

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A block whose mass is 650 gm is fastened to aspring constant K equals 65 N/m whose other end is fixed. The block is pulled a distance x = 11 cm from its equilibrium position at x = 0 on a smooth surface, and released from rest at t = 0. The maximum speed ‘S’ of the oscillating block is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The angle between the axes of two shafts connected by Hooke’s joint is 18°. Determine the angle turned through by the driving shaft when the velocity ratio is maximum.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Two shafts having an included angle of 150° are connected by a Hooke’s joint. The driving shaft runs at a uniform speed of 1500 r.p.m. The driven shaft carries a flywheel of mass 12 kg and 100 mm radius of gyration. Using the above data, calculate the maximum angular acceleration of the driven shaft in rad/s^2.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Two shafts having an included angle of 150° are connected by a Hooke’s joint. The driving shaft runs at a uniform speed of 1500 r.p.m. The driven shaft carries a flywheel of mass 12 kg and 100 mm radius of gyration. Using the above data, calculate the maximum torque required in N-m.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Two shafts with an included angle of 160° are connected by a Hooke’s joint. The driving shaft runs at a uniform speed of 1500 r.p.m. The driven shaft carries a flywheel of mass 12 kg and 100 mm radius of gyration. Find the maximum angular acceleration of the driven shaft.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

While designing a screw in a screw jack against buckling failure, the end conditions for the screw are taken as

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A Hooke’s joint is used to connect two

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Double hooke’s joint can be used to keep the angular velocity of the shaft constant.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Multiple threads are used to secure

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following screw thread is used for lead screw of lathe?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following screw thread is used for jacks, vices and clamps?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following screw thread is used for transmitting force in one direction?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In automobiles, Hooke’s joint is used between which of the following?

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The material used for lining of friction surfaces of a clutch should have _____________ coefficient of friction.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Screws used for power transmission should have

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A body of mass 1 kg is kept on a rough surface is being pulled by a force of 2N, what will be the value of coefficient of friction if it just begins to move. Take g = 10m/s^2.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

Greg · Answer 1 · 2022-10-19T05:22:46+0000

The correct option is (b) step bearings

Easiest explanation: Step bearing is used to resist the end thrust of the shafts.

__________ is used to resist the end thrust of the shafts.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories