In the given figure if N1 is the node then N1Q acts as which of the following system?

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

the given figure, considering left end has one rotor, If the mass moment of inertia of the shaft till node N1 is increased to four times, then what will be the effect on free torsional vibrations of a rotor at left end of N1?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the given figure if N is the node then NQ acts as which of the following system?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the figure given below, the points N1 and N2 are known as_______

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a three rotor system in the figure given below, the length of one shaft(P) is twice the other(Q), then what is the relation between the Mass moment of inertia of the shafts.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a three rotor system, free torsional vibration cannot occur if there is only one node.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Keeping the mass moment of inertia of left end and the right end shafts in a three rotor system same, if the length of one shaft is doubled what should be the effect on the length of other shaft?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

What is the total number of nodes formed in a three rotor system if the rotors at one of the ends and the one in the middle rotate in the same direction?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a three rotor system, for the middle rotor, if the stiffness of both the length either side of the rotor is increased to two times what will be the effect on total stiffness of the middle rotor?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Free torsional vibrations will occur in a three rotor system only if all rotors have same frequency.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For occurrence of free torsional vibration in a three rotor system which of the condition is necessary?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the given figure, considering PN as one shaft, If the mass moment of inertia is increased to four times, then what will be the effect on free torsional vibrations of a rotor at P?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In which of the following condition torsional vibration will not take place, considering 3 rotors A, B and C. A is rotating in clockwise direction.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A single cylinder oil engine works with a three rotor system, the shaft length is 2.5m and 70mm in diameter, the middle rotor is at a distance 1.5m from one end. Calculate the free torsional vibration frequency for a two node system in Hz if the mass moment of inertia of rotors in Kg-m^2 are: 0.15, 0.3 and 0.09. C=84 kN/mm^2

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A single cylinder oil engine works with a three rotor system, the shaft length is 2.5m and 70mm in diameter, the middle rotor is at a distance 1.5m from one end. Calculate the free torsional vibration frequency for a single node system in Hz if the mass moment of inertia of rotors in Kg-m^2 are: 0.15, 0.3 and 0.09. C=84 kN/mm^2

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the given figure representing a two rotor system, what is the line LNM called?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Consider P and Q as the shaft having two rotors at the end of it, what is the point N known as in the given figure?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the mass of the constraint is negligible and a mass is attached at the end of the rod having following values: Ic = 500 Kg-m^2 and ω= 10 rad/s, then calculate the kinetic of the constraint system.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the mass of the constraint is negligible then what is the kinetic energy of the system?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the polar moment of inertia is increased to four times, then what will be the effect on free torsional vibrations of a single motor system?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the length inertia is decreased to nine times, then what will be the effect on free torsional vibrations of a single motor system?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the mass moment of inertia is increased to four times, then what will be the effect on free torsional vibrations of a single motor system?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the damper is not provided and the system is in resonance, which of the following is the correct isolation factor?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a vibration system having different shaft parameters, calculate which of the following cannot be the diameter of the equivalent shaft if the diameters of shafts in m are: 0.05, 0.06, 0.07.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When inertia of gearing is taken into consideration, then an additional shaft must be introduced in the equivalent system of the rotors connected by the shaft.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a two rotor system, the mass moment of inertia of one shaft(A) is twice the other(B), then what is the relation between the length of the shafts.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

...