When brakes are applied to all the four wheels of a moving car, the distance travelled by the car before it is brought to rest, will be

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

The combined mass of bicycle and rider is 100 kg, they are travelling at the speed of 16 km/h on a level road. Diameter of rear wheel is 0.9m. The pressure applied on the brake is 100 N and μ = 0.05., find the no. of revolutions made by the bicycle before it comes to rest.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A car starts from rest and accelerates uniformly to a speed of 72 km. p.h. over a distance of 500 m. A further acceleration raises the speed to 90 km. p.h. in 10 seconds.The brakes are now applied to bring the car to rest under uniform retardation in 5 seconds. Find the distance travelled during braking.

asked Sep 23, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A car moving with speed u can be stopped in minimum distance x when brakes are applied. If the speed becomes n times, the minimum distance over which the car can be stopped would take the value

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Which of the following type of brakes can bring the member to an absolute rest?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The combined mass of bicycle and rider is 100 kg, they are travelling at the speed of 16 km/h on a level road. Diameter of rear wheel is 0.9m. How far will the bicycle travel after the application of brake? The pressure applied on the brake is 100 N and μ = 0.05.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Electric brakes are used to control the speed of vehicle during downhill travel.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The brake shown in figure has a coefficient of friction 0.25 and is to operate using a maximum force F of 500 N. Assume width of the band to be 50 mm. Find the maximum band tension. All dimensions are in mm.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The brakes commonly used in railway trains is

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In which of the following brakes the force acting on the brake drum is in axial direction?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a belt transmission dynamometer, if the diameter of pully is doubled and speed of rotation is halved, then the new braking power will be ________

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A disc spinning on its axis at 20 rad/s will undergo precession when a torque 100 N-m is applied about an axis normal to it at an angular speed, if mass moment of inertia of the disc is the 1 kg-m^2

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Light is visible when the torque is being transmitted by the shaft.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A Pickering governor is driving a gramophone. Each disc attached to the centre of a leaf spring has a mass of 20 g. The width of each spring is 5 mm and thickness of 0.125 mm. The effective length of each spring is 40 mm. The distance from the spindle axis to the centre of gravity of the mass when the governor is at rest, is 10 mm, find the speed of the turntable in rpm if ratio of the governor speed to the turntable speed is 10.5.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A Pickering governor is driving a gramophone. Each disc attached to the centre of a leaf spring has a mass of 20 g. The width of each spring is 5 mm and thickness of 0.125 mm. The effective length of each spring is 40 mm. The distance from the spindle axis to the centre of gravity of the mass when the governor is at rest, is 10 mm. Find the speed of the governor in rpm when the sleeve has risen to a height of 0.8 mm. (E = 210kN/mm^2)

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For which of the following dynamometers the driving torque on the shaft is not uniform and it is subjected to severe oscillations?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The brake shown in figure has a coefficient of friction 0.25 and is to operate using a maximum force F of 500 N. Assume width of the band to be 50 mm, find the braking torque.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When the fulcrum is between the two ends of a lever, the type of brake is _____

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

To prevent the rotation caused by frame, which of the following quantity is added?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the friction of the pin on which the pinion rotates is neglected, which of the following force is equal to the tangential effort exerted by the spur gear on the pinion

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A motor car has a wheel base of 2.73 m and pivot centre of 1.065 m. the front and rear wheel track is 1.217 m. What will be angle of outside lock and turning circle radius of the outer front and inner rear wheels when the angle of inside lock is 40°?

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

The lamp and the eye piece must be moved _______ so as to bring them into line.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When the shaft is transmitting torque, which of the following phenomenon occurs?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When the shaft is transmitting torque, which of the following phenomenon can cause visibility of light in the eyepiece?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When the shaft is not transmitting torque, which of the following phenomenon occurs?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

An Internal combustion engine has a connecting rod of mass 2 kg and the distance between the centre of crank and centre of gudgeon pin is 25 cm. The Center of Gravity lies at a point 10 cm from the gudgeon pin along the line of centres. The radius of gyration of this system about an axis through the Center of Gravity perpendicular to the plane of rotation is 11 cm. If two masses are used instead of the connecting rod, one at the gudgeon pin and other at the crank pin. What will be the new radius of gyration?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

...