Which of the following statement is correct? (a)The power absorbed in operating the piston valve is less than D-slide valve.

Question

Which of the following statement is correct? (a)The power absorbed in operating the piston valve is less than D-slide valve.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

In a steam engine, the distance by which the inner edge of the D-slide valve overlaps the steam port is called lead.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a steam engine, the distance by which the outer edge of the D-slide valve overlaps the steam port is called

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The displacement of the D-slide valve is ______________ the steam lap by a distance known as lead of the valve.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The piston slide valve is an inside admission valve.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The distance by which the _____________ of the D-slide valve overlaps the steam port is called exhaust lap.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The D-slide valve is also known as

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a steam engine, one method of obtaining the earlier cut-off with a simple slide valve is by increasing the steam lap and the angle of the eccentric but keeping constant the travel and lead of the valve. This method will

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a steam engine, one method of obtaining the earlier cut-off with a simple slide valve may be obtained by increasing the angle of advance of the eccentric but reducing the throw of the eccentric and keeping the steam lap and exhaust lap constant. The method will cause withdrawing or throttling of steam.

asked Sep 21, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The virtue or equivalent eccentric for the Meyer’s expansion valve is defined as an eccentric having such a length and angle of advance that will cause cut-off to take place at the same position, as is caused by the combined effect of main eccentric and expansion eccentric.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In Meyer’s expansion valve, the expansion valve is driven by an eccentric having an angle of advance from

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In Meyer’s expansion valve, the main valve is driven by an eccentric having and angle of advance from

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The distance moved by the valve from one end to the other end is called valve travel.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The throw of the eccentric is equal of the valve travel.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When the load on the engine increases, it becomes necessary to increase the supply of working fluid and when the load decreases, less working fluid is required. The supply of the working fluid to the engine is controlled by a

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A flywheel is used to control the mean speed of an engine caused by the variations in load.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The function of a reversing gear in a steam engine is

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The entire energy or power produced by the engine is absorbed by the friction resistances of the brake in which of the following dynamometers does?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In which of the following dynamometers does the entire energy or power produced by the engine is absorbed by the friction resistances of the brake?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The crank-pin circle radius of a horizontal engine is 300 mm. The mass of the reciprocating parts is 250 kg. When the crank has travelled 30° from T.D.C., the difference between the driving and the back pressures is 0.45 N/mm^2. The connecting rod length between centres is 1.2 m and the cylinder bore is 0.5 m. If the engine runs at 250 r.p.m. and if the effect of piston rod diameter is neglected, calculate the net load on piston.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Which of the following statement is correct? (a)In any engine, 100% of the reciprocating masses can be balanced dynamically

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Consider two governors A and B running at the same speed. When this speed increases or decreases by a certain amount, the lift of the sleeve of governor A is greater than the lift of the sleeve of governor B. Which of the following statement is true for the above situation?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Considering a four bar chain with each link having linear and angular acceleration, applying D-Alembert’s principle will never result in which of the following member?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the given figure, the velocity of piston is maximum under which of the following conditions?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When engine torque is less than mean resisting torque, then the flywheel _______

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If OC is the crank and PC is the connecting rod of a reciprocating steam engine and rotates with uniform angular velocity in clockwise direction in the given figure below: then under which condition the piston will undergo retardation?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

Fred · Answer 1 · 2022-10-14T12:57:11+0000

The correct choice is (d) all of the mentioned

Explanation: All the statements are correct.

Which of the following statement is correct? (a)The power absorbed in operating the piston valve is less than D-slide valve.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories