Rectangular notch may or may not have ventilation.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

We need to obligatorily have ventilation in triangular notch.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

What is main reading required in calculation for rectangular notch or weir.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

The results of which are more accurate; rectangular notch or triangular weir.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

Find the discharge of water flowing over a rectangular notch of 1.5 m length when the constant head over the notch is 275 mm. Take Cd = .60

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

Find the discharge of water flowing over a rectangular notch of 1.3 m length when the constant head over the notch is 255 mm. Take Cd = .62

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

The head of water over a rectangular notch is 700 mm. The discharge is 200 litres/s. Find the length of the notch, when CD =.63

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

The head of water over a rectangular notch is 900 mm. The discharge is 300 litres/s. Find the length of the notch, when CD =.62

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

The expression for discharge for a right angled notch is more complex than rectangular notch.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

Find the discharge over triangular notch of angle 50° when the head over the V notch

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

The MoM (Material of Manufacture) of notch is,

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

The notch is bigger in size than wier.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

A notch is a device used to measure the turbulence of the flowing liquid directly.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

Which of the following is not a way of classifying notches or weirs?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

Find the discharge through a rectangular orifice 2.2 m wide and 1.3 m deep fitted to a easier tank. The water level in a team is 2.5 m above the top edge of orifice.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

The head of water over a rectangular weir is 28 cm. The length of the crest of the weir end contraction suppressed is 1.27 m. Find the discharge using the Francis formula.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

A rectangular orifice of 2 m width and 1.2 m deep is fitted in one side of large tank. The easier level on one side of the orifice is 3m above the top edge of the orifice while on the other side of the orifice the water level is 0.5 m below it’s top edge. Calculate discharge if Cd = .64

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

The head of water over a rectangular weir is 38 cm. The length of the crest of the weir end contraction suppressed is 1.3 m. Find the discharge using the Francis formula.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

Find the discharge through a rectangular orifice 3.2 m wide and 1.7 m deep fitted to a easier tank. The water level in a team is 3.3 m above the top edge of orifice. Take Cd = 0.6

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

The head of water over a rectangular weir is 26 cm. The length of the crest of the weir end contraction suppressed is 1.25 m. Find the discharge using the Francis formula.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

Which of the following is not a way of classifying based on the shape of opening?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

What is not the way of classifying weir based on the emerging nappe?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

What is not the way of classifying weir based on their shape of crest?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

An Ogee weir 3.4 m long had a head of 40 cm of water. If CD = 0.63 find the discharge over the weir.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

For discharge over ogee weir discharge is directly proportional to length but for discharge over narrow crested weir it is inversely proportional to length.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

In Francis empirical expression for discharge, the relation between head of water and discharge is

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

...