In case of any orifice, velocity always remains constant and hence discharge can be calculated.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

In case of submerged orifice the discharge is substantially dependent on temperature of fluid

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

Find the discharge through totally drowned orifice of width 2.3 m if the difference of water levels on both side of the orifice be 40 cm. The height of water from to and bottom of the orifice are 2.6 m and 2.75 m respectively.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

When is orifice called ‘large orifice’?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

Orifice Meter can only be used for measuring rate of flow in open pipe like structure.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

What is the term used for a case where source and sink( both of them are of equal magnitude) approach each other such, distance between them reduces and product of distance and discharge magnitude remains constant.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A nanometre is connected to a section which is at a distance of about 4 to 6 times the pipe diameter upstream from orifice plate.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

Orifice meter consists of a flat rectangular plate.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A large tank is filled with three liquids of densities ρ, 2ρ and 3ρ up to heights of ^h ⁄ 6, ^h ⁄ 3 and ^h ⁄ 2 respectively. What will be the ratio of the instantaneous velocity of discharge through a small opening at the base of the tank in this case to that if the container is filled with the liquid of density ρ only? (assume that the diameter of the opening is negligible compared to the height of the liquid column)

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

The below figure shows a pipe with a circular cross section of diameter 5 cm on the left end and a square cross section with diagonal 5 cm on the right end. Water enters the left end with a velocity 20 m/s and leaves the right end with a velocity V2. Find V2 (neglect losses in the pipe).

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A water flows through a pipe at a velocity 2 m/s. The pressure gauge reading is 2 bar. The datum head is given to be 2 m. Find the piezometric head. (Assume all Bernoulli’s assumptions, Density of water = 1000 kg/m^3, g = 9.8 m/s^2).

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

A student wishes to find the velocity of air flowing through a pipe. He has a pressure gauge which displays only the dynamic pressure. The pressure gauge reads 0.018 mm Hg. Assume density of air to be 1.225 kg/m^3, find the velocity V of air (ρHg = 13600 kg/m^3).

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

The Navier- Stokes equation can be used in which of the following applications?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

What are the Newtonian constitutive assumptions regarding relationship between stress tensor and velocity gradients?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

If a flow is having the same parameters at any given point, then it is said to be_________

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

Which is the cheapest device for measuring flow / discharge rate.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

Find the discharge through totally drowned orifice of width 3.3 m if the difference of water levels on both side of the orifice be 50 cm. The height of water from to and bottom of the orifice are 2.25 m and 2.67 m respectively.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

The velocity profile of the Couette flow is _______

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

The best place to place a pitot tube on an aircraft for velocity measurement is just behind the jet engine.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

What is the velocity profile for Poiseuille flow?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

Find the discharge through a rectangular orifice 2.2 m wide and 1.3 m deep fitted to a easier tank. The water level in a team is 2.5 m above the top edge of orifice.

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

A rectangular orifice of 2 m width and 1.2 m deep is fitted in one side of large tank. The easier level on one side of the orifice is 3m above the top edge of the orifice while on the other side of the orifice the water level is 0.5 m below it’s top edge. Calculate discharge if Cd = .64

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

Find the discharge through a rectangular orifice 3.2 m wide and 1.7 m deep fitted to a easier tank. The water level in a team is 3.3 m above the top edge of orifice. Take Cd = 0.6

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

In the equation, the unit of E CANNOT be written as ______

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+2 votes

1 answer

Sum of enthalpy and kinetic energy remains a constant in __________

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

+1 vote

1 answer

Which among the following cannot be used as an alternative term for a “solenoidal vector field”?

asked Jan 30, 2022 in Fluid Mechanics by Charlotte (118k points)

...