A compound gear train consists of at least 3 shafts connected to each other.

Question

A compound gear train consists of at least 3 shafts connected to each other.

1 Answer

Related questions

0 votes

0 answers

If centre distance between the two gears on same shaft is unequal to the centre distance on the other two gears on the second shaft, then this gear train is called reverted gear train.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which of the following are true about epicyclic gear train?

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If driving gear rotates in CW, then driven gear will rotate in?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If driving gear rotates ACW, driven gear will rotate in which direction?

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If driving gear rotates CW, driven gear will rotate?

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Gear drive don’t require precise alignment of shafts.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A herringbone speed reducer consist of 20 teeth pinion driving a 100 teeth gear. The normal module of gear is 2mm. The face width of each half is 30mm and Lewis factor is 0.4. Calculate the material constant K if surface hardness is 400BHN.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A herringbone speed reducer consist of 20 teeth pinion driving a 100 teeth gear. The normal module of gear is 2mm. The face width of each half is 30mm and Lewis factor is 0.4. If permissible bending stress is 500N/mm², then calculate the beam strength.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Is it possible to transmit power between shafts lying in different planes using gears?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The direction of tangential component for a driving gear is same to the direction of rotation.

asked Jan 21 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which of the following lubricant has least rate of change of viscosity w.r.t temperature.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Helical gears mounted on parallel shafts are called crossed helical gears.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the transverse pressure angle in degrees.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the pitch circle diameter of pinion.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the dedendum circle diameter of the pinion.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the pitch circle diameter of the gear.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of spur gears consist of 25 teeth pinion meshing with a 115 teeth gear. The module is 5mm. Calculate pitch circle diameter of the pinion.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of helical gears consist of 25 teeth pinion gear meshing with a 90 teeth gear. Calculate the material constant k If surface hardness is 260BHN.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the torque on the gear A.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of spur gears consist of 25 teeth pinion meshing with a 115 teeth gear. The module is 5mm. Calculate the centre distance.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Below is a representation of a helical gear. Blue lines in the figure signify?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate addendum circle diameter of the pinion.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A pair of spur gears consist of 25 teeth pinion meshing with a 115 teeth gear. The module is 5mm. Calculate the addendum.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A pair of helical gears consist of 25 teeth pinion gear meshing with a 90 teeth gear. Calculate the wear strength If surface hardness is 260BHN. Also face width=35mm, module=4mm and helix angle=25⁰.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A pair of spur gears consist of 25 teeth pinion meshing with a 115 teeth gear. The module is 5mm. Calculate the tooth thickness.

asked Jan 22 in Machine Design by Carter (89.5k points)

Chris · Answer 1 · 2026-01-27T10:54:13+0000

The optimal answer is (b) False

For a clear picture: A compound gear train is characterised by one shaft carrying two gears atleast.

A compound gear train consists of at least 3 shafts connected to each other.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories