If driving gear rotates ACW, driven gear will rotate in which direction?

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

If driving gear rotates in CW, then driven gear will rotate in?

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If driving gear rotates CW, driven gear will rotate?

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If centre distance between the two gears on same shaft is unequal to the centre distance on the other two gears on the second shaft, then this gear train is called reverted gear train.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which of the following are true about epicyclic gear train?

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A compound gear train consists of at least 3 shafts connected to each other.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The direction of tangential component for a driving gear is same to the direction of rotation.

asked Jan 21 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A herringbone speed reducer consist of 20 teeth pinion driving a 100 teeth gear. The normal module of gear is 2mm. The face width of each half is 30mm and Lewis factor is 0.4. Calculate the material constant K if surface hardness is 400BHN.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A herringbone speed reducer consist of 20 teeth pinion driving a 100 teeth gear. The normal module of gear is 2mm. The face width of each half is 30mm and Lewis factor is 0.4. If permissible bending stress is 500N/mm², then calculate the beam strength.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of helical gears consist of 25 teeth pinion gear meshing with a 90 teeth gear. Calculate the material constant k If surface hardness is 260BHN.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A pair of helical gears consist of 25 teeth pinion gear meshing with a 90 teeth gear. Calculate the wear strength If surface hardness is 260BHN. Also face width=35mm, module=4mm and helix angle=25⁰.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Among spur gear and helical gear, which has smooth engagement and thus lesser noise?

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the transverse pressure angle in degrees.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Below is a representation of a helical gear. Blue lines in the figure signify?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

There is same type of tooth meshing in helical and spur gear.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Interference is maximum when the largest pinion is in mesh with the smallest gear.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Herringbone gear can be used in

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Gear drive don’t require precise alignment of shafts.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

There are ____ standard systems for the shape of gear teeth.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the pitch circle diameter of pinion.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the dedendum circle diameter of the pinion.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Crowning is an abrasive process that debars the gear strength.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the pitch circle diameter of the gear.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of spur gears consist of 25 teeth pinion meshing with a 115 teeth gear. The module is 5mm. Calculate pitch circle diameter of the pinion.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the torque on the gear A.

asked Jan 25 in Machine Design by Carter (89.5k points)

...