Name the filter that has two stop bands?

Question

Name the filter that has two stop bands?

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

Determine the order of filter used, when the gain increases at the rate of 60dB/decade on the stop band.

asked Jan 15 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

Which among the following has the best stop band response?

asked Nov 16, 2023 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

Match the gain of the filter with the frequencies in the low pass filter Frequency Gain of the filter 1. f < fH i. VO/Vin ≅ AF/√2 2. f=fH ii. VO/Vin ≤ AF 3. f>fH iii. VO/Vin ≅ AF

asked Mar 16 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

In which filter the output and input voltages are equal in amplitude for all frequencies?

asked Mar 16 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

An electrical filter is a

asked Mar 16 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

In a low pass butterworth filter, the condition at which f=fH is called

asked Mar 16 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

To change the high cutoff frequency of a filter. It is multiplied by R or C by a ratio of original cut-off frequency known as

asked Jan 15 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

Using the frequency scaling technique, convert 10kHz cut-off frequency of the low pass filter to a cutoff frequency of 16kHz.(Take C=0.01µF and R=15.9kΩ)

asked Jan 15 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

The gain of the first order low pass filter

asked Jan 15 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

Find the High cut-off frequency if the pass band gain of a filter is 10.

asked Jan 13 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

Determine the gain of the first order low pass filter if the phase angle is 59.77^o and the pass band gain is 7.

asked Jan 13 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

Find the complex equation for the gain of the first order low pass butterworth filter as a function of frequency.

asked Jan 13 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

Find the difference in gain magnitude for a filter ,if it is the response obtained for frequencies f1=200Hz and f2=3kHz. Specification: AF=2 and fH=1kHz.

asked Nov 16, 2023 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

The problem of passive filters is overcome by using

asked Mar 16 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

Find out the incorrect statement about active and passive filters.

asked Mar 16 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

Why inductors are not preferred for audio frequency?

asked Mar 16 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

Find the voltage across the capacitor in the given circuit

asked Mar 16 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

What are the most commonly used active filters?

asked Jan 15 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

Frequency scaling is done using

asked Jan 13 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

Filters are classified as

asked Jan 13 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

Name the resistor that is connected in the non-inverting terminal of op-amp which is in parallel combination of resistor connected in inverting terminal and feedback resistor.

asked Mar 16 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

Name the resistive transducer that varies its resistance on application of external stress?

asked Jan 13 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

Name the process that is used to overcome the increase in collector series resistance, which occurs due to the presence of collector contact at the top of integrated transistor.

asked Jan 13 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

Which of the following has the same characteristic as that of non-inverting amplifier with feedback?

asked Mar 16 in Linear Integrated Circuits by Julian (38.2k points)

+1 vote

1 answer

In Schottky barrier diode, which contact has similar characteristics to that of an ordinary PN diode?

asked Mar 16 in Linear Integrated Circuits by Julian (38.2k points)

Chris · Answer 1 · 2024-03-15T17:05:20+0000

Correct answer is (a) Band-pass filter

Simply put: A band-pass filter has two stop bands: 1) 0 < f < fL and 2) f > fH.

Name the filter that has two stop bands?

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories