In high dams, the safety against sliding should be checked only for friction.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

What is the recommended value of shear friction factor against sliding?

asked Sep 25, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

The small openings made in the huge body of a concrete gravity dam such as sluices and inspection galleries can be assumed to be causing only local effects without any appreciable effect on the distribution of stresses as per the principle of_____________________

asked Nov 9, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

A concrete gravity dam having a maximum reservoir level at 200 m and the RL of the bottom of the dam 100 m. The maximum allowable compressive stress in concrete is 3000 KN/m^2 and the specific gravity of concrete is 2.4. Calculate the height of the dam and check whether it is a high dam or low dam.

asked Sep 25, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

For full reservoir condition in a gravity dam, the critical combination of vertical and horizontal earthquake accelerations to be considered for checking the stability is ________________________

asked Sep 5, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

The vertical stress at the toe was found to be 3.44 MPa at the base of the gravity dam section. If the downstream face of the dam has a slope of 0.617 horizontal: 1 vertical, the maximum principal stress at the toe of the dam when there is no tailwater is _______________

asked Sep 5, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

Presence of tail-water in a gravity dam ____________________

asked Nov 9, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

The base width of a solid gravity dam is 35 m and the specific gravity of dam material is 2.45. What is the approximate allowable height of the dam having an elementary profile without considering the uplift?

asked Sep 25, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

The axis of a gravity dam is the ______________________

asked Sep 25, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

A low gravity dam of elementary profile made up of concrete of relative density 2.57 and safe allowable stress of foundation material 4.2 MPa. What is the maximum height of the dam without considering the uplift force?

asked Sep 5, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

What is the average value of acceleration that is sufficient for high dams in seismic zones?

asked Nov 16, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

The factor of safety against overturning generally varies between ___________

asked Nov 16, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

The two-dimensional stability analysis of gravity dams proves better for U-shaped valleys than for V-shaped valleys.

asked Nov 16, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

Transverse joints in concrete gravity dams are the ___________________________

asked Nov 9, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

For the design of gravity dam, the minimum value of F(factor of safety) against sliding should be __________

asked Feb 8, 2022 in Geotechnical Engineering II by Amelia (93.8k points)

+1 vote

1 answer

Calculate the value of free-board that should be provided for a reservoir having a wind velocity of 92 km/h and it extends up to 18 km upstream.

asked Sep 25, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

Which of the following joints justifies the two-dimensional analysis of gravity dams?

asked Sep 26, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

The governing compressive stress in a concrete gravity dam which should not be allowed to exceed the permissible value of about 3000 KN/m^2 while analyzing full reservoir case is ____________________

asked Nov 9, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

Calculate the value of minimum base width for an elementary triangular concrete gravity dam supporting 72 m height of reservoir water and full uplift? (Take specific gravity of concrete as 2.4 and coefficient of friction as 0.7)

asked Nov 16, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

For usual values of permissible compressive stress and specific gravity of concrete, a high concrete gravity is the one whose height exceeds ______________

asked Nov 16, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

What is the maximum permissible tensile stress for high concrete gravity dam under worst conditions?

asked Sep 5, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

What is the value of horizontal destabilizing force caused by the formation of waves in a storage reservoir having a fetch of 52 km due to high wind of 172 km/h?

asked Sep 25, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

Which of the following criteria has to be satisfied for no tension at any point on a gravity dam?

asked Nov 9, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

What is the value of eccentricity for no tension condition in the dam?

asked Nov 16, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

For triangular dam section of height H for just no tension under the action of water pressure, self-weight and uplift pressure, the minimum base width required is _____________

asked Nov 16, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

The general value of lift for concrete is taken as __________________

asked Nov 9, 2023 in Irrigation Engineering by Carter (75.2k points)

...