Design of alluvial channels in India is based on Kennedy and Lacey theories.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

What vital factor is not considered in regime theories during the design of regime channels?

asked Aug 16, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

Based on his research what factor is given by Kennedy for free silting and scouring actions in a channel?

asked Aug 15, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

According to Kennedy the silting action in channels is due to?

asked Aug 15, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

What is the problem in India for artificial channels?

asked Aug 25, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

According to Lacey what factor is needed to have a true regime in an artificial channel?

asked Aug 19, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

Which type of state is achievable in artificial channels but not in rivers?

asked Aug 16, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

What is the effect of scouring in channels?

asked Aug 15, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

What is the effect of silting in channels?

asked Jul 31, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

Design a regime channel for a discharge of 90 cumecs and silt factor is 1.3 use Lacey’s Theory.

asked Aug 25, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

Given to design the irrigation channel to carry 80 cumecs of discharge. The channel slope is 1 in 3000. The critical velocity ratio is 1.3. Take rugosity coefficient as 0.021.

asked Jul 31, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

On what condition does the resistance equations of Chezy’s formula and manning’s formula are applicable?

asked Aug 16, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

On what basis for designing the regime state is obtained?

asked Aug 15, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

The velocity of flow in a channel should not more or less, but instead it should be adequate.

asked Aug 15, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

For the design of non-scouring channels in coarse alluviums, the shield’s entrainment function should be ____________

asked Aug 16, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

Calculate the effective unit tractive force that causes bed load transportation if the unit tractive force produced by the flowing water is 3.20 N/m^2. The Manning’s coefficient on an unrippled bed is 0.0108 and the actual observed value of Manning’s coefficient on ripped channels is 0.0222. Take the value of critical shear stress that is required to move the grain particle as 0.5 N/m^2.

asked Sep 16, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

Strickler’s formula is only applicable to the flexible boundary channels.

asked Jul 29, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

Design a channel carrying a 30 cumecs. The median grain diameter is taken as 0.5 mm. The bedload concentration is 60 p.p.m by weight. Use Lacey’s Regime perimeter and Meyer-peter’s formulas.

asked Jul 29, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

Which of the following statement is wrong? (a)The design and execution of flood control scheme is chiefly governed by the peak flood levels

asked Jul 29, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

Calculate the corresponding hydraulic mean depth that would exist in the channel if the bed was unrippled. The rugosity coefficient in an unrippled channel is 0.015 and the rugosity coefficient actually observed by experiments on the rippled bed of channel is 0.020. Consider the value of hydraulic mean depth of the channel as 1.5 m.

asked Aug 19, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

A pump was installed in a field to supply water to the crops. The duty for this crop is 432 hectares/cumec on the field and the efficiency of pump is 50%. The sown area of the field is 5 hectares. Determine the maximum output required (H.P) of the pump, if the highest water level is 4 meters below the highest portion of the field. Assume negligible field channel losses.

asked Aug 16, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

Let us consider in a given area the plantation of a certain crop takes 20 days, and the total water depth required by this crop is 80 cm on the field. Find the duty of irrigation water required for the crop during this period. (a) Assuming 20% losses of water in the water courses, find duty at the head of the course. (b) Find the duty of the water at the head of the distributary, assuming 10% losses from the distributary head.

asked Jul 31, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

At a certain place, the transplantation of a crop takes 15 days, and the total depth of water required by the crop is 90 cm on the field. During the plantation rain falls and about 20 cm is utilised to fulfil the demand. Now determine the duty of irrigation water required during the plantation.

asked Aug 15, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

Determine the shear stress required to move the single grain on the side slopes, if the critical shear stress required moving the similar grain on the horizontal bed is 2.91 N/m^2. Consider the angle of the side slope with the horizontal as 30° and the angle of repose of soil as 37°.

asked Jul 29, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

The scouring and silting on the river banks raise the flood levels for the particular discharge.

asked Jul 29, 2023 in Irrigation Engineering by Carter (75.2k points)

+1 vote

1 answer

A wide unlined channel carrying silt-free water has a depth of 2.0 m. The maximum slope that can be given to a channel is 1 in 10,000. Calculate the maximum tractive stress permissible on the bed to prevent scouring.

asked Jul 31, 2023 in Irrigation Engineering by Carter (75.2k points)

...