For the given figure, the brake can sustain a torque of 350 N-m and coefficient of friction between the band and drum is 0.3, If the drum rotates in anticlockwise direction, find force in N.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

For the given figure, the brake can sustain a torque of 350 N-m and coefficient of friction between the band and drum is 0.3, find necessary force required for clockwise rotation of the drum in N.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For the given figure, the brake can sustain a torque of 350 N-m and coefficient of friction between the band and drum is 0.3, find OA for self locking condition during clockwise rotation.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The brake shown in figure has a coefficient of friction 0.25 and is to operate using a maximum force F of 500 N. Assume width of the band to be 50 mm, find the braking torque.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The brake shown in figure has a coefficient of friction 0.25 and is to operate using a maximum force F of 500 N. Assume width of the band to be 50 mm. Find the maximum band tension. All dimensions are in mm.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a simple band brake, the fulcrum is at the end of the lever.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Braking torque is independent of the radius of drum.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When the fulcrum is between the two ends of a lever, the type of brake is _____

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In which of the following brakes the force acting on the brake drum is in axial direction?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Which of the following brake does not has self locking?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The combined mass of bicycle and rider is 100 kg, they are travelling at the speed of 16 km/h on a level road. Diameter of rear wheel is 0.9m. The pressure applied on the brake is 100 N and μ = 0.05., find the no. of revolutions made by the bicycle before it comes to rest.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A simple band brake has the tight side of the band attached to a fixed pivot. The angle of wrap is 280° about a 450-mm diameter drum. A torque of 170 mm is sustained at 900 revs min^-1. If the co-efficient of friction is 0.2 the required belt tension at tight side of the belt will be _____

asked Jan 29, 2022 in Farm Machinery by Olivia (38.9k points)

+1 vote

1 answer

If the friction of the pin on which the pinion rotates is neglected, which of the following force is equal to the tangential effort exerted by the spur gear on the pinion

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The combined mass of bicycle and rider is 100 kg, they are travelling at the speed of 16 km/h on a level road. Diameter of rear wheel is 0.9m. How far will the bicycle travel after the application of brake? The pressure applied on the brake is 100 N and μ = 0.05.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Flywheel diameter 1.2 m; diameter of the rope 12.5 mm; engine speed 200 r.p.m.; dead load on the brake 600 N; spring balance reading 150 N. Using this data, calculate the brake power of the engine in kW.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Flywheel diameter 1.2 m; diameter of the rope 12.5 mm; engine speed 400 r.p.m.; dead load on the brake 600 N; spring balance reading 150 N. Using this data, calculate the brake power of the engine in kW.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Flywheel diameter 1.2 m; diameter of the rope 12.5 mm; engine speed 100 r.p.m.; dead load on the brake 600 N; spring balance reading 150 N. Using this data, calculate the brake power of the engine in kW.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If OC is the crank and PC is the connecting rod of a reciprocating steam engine and rotates with uniform angular velocity in clockwise direction in the given figure below: then under which condition the piston will undergo retardation?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A shaft fitted with a flywheel rotates at 250 r.p.m. and drives a machine, the torque fluctuated about 18750 N-m, find the power required to drive the machine.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the given figure if the angle between OA and x-axis is made 90 degrees, the rotation speed will become 0. (the x – axis represents radius of rotation and the y axis represents the controlling force.)

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A 60 mm diameter shaft running in a bearing carries a load of 2000 N. If the coefficient of friction between the shaft and bearing is 0.03, find the power transmitted when it runs at 1440 r.p.m.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A ship propelled by a turbine rotor which has a mass of 5 tonnes and a speed of 2100 r.p.m. The rotor has a radius of gyration of 0.5 m and rotates in a clockwise direction when viewed from the stern. Find the gyroscopic effect when the ship sails at a speed of 30 km/h and steers to the left in a curve having 60 m radius.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A multiple disc clutch has five plates having four pairs of active friction surfaces. If the intensity of pressure is not to exceed 0.127 N/mm^2, find the power transmitted at 500 r.p.m. The outer and inner radii of friction surfaces are 125 mm and 75 mm respectively. Assume uniform wear and take coefficient of friction = 0.3.

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In the given figure, m1=20 Kg, m2=30Kg and m=50 Kg, if r1=0.2m and r=0.3m, l=1m, find l2.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the given figure, m1=10 Kg, m2=30Kg and m=50 Kg, if r=0.3m, l=1m, find l2 = 0.5m, find r1 in m.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In the given figure, m1=10, Kg m2=30Kg and m=50 Kg, if r1=0.2m and r=0.3m, l=1m, find l2.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

...