Unit of damping factor is N/m/s.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

The ratio of the actual damping coefficient (c) to the critical damping coefficient (cc ) is known as _________

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Magnification factor is the ratio of the maximum displacement due to forced vibrations to the deflection due to _______

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In which of the cases the factor c = 0?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Maximum displacement due to forced vibration is dependent on deflection due to static force.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A body of mass 20 kg is suspended from a spring which deflects 20mm under this load. Calculate the frequency of free vibrations in Hz.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the mass increases, then the frequency of the free vibrations increases.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In vibration isolation system, if ω/ωn < 2, then for all values of damping factor, the transmissibility will be

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Fluid resistance causes damping which is known as ______

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In steady state forced vibrations, the amplitude of vibrations at resonance is _____________ damping coefficient.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In which direction does the damping force acts?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The factor which affects the critical speed of a shaft is

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m^3. Determine the static deflection of the shaft in mm.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m^2. Determine the frequency of transverse vibrations of the shaft.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m^2. Calculate the natural longitudinal frequency in Hz.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Assuming the shaft to be freely supported. Calculate the whirling speed of the shaft : 2 cm diameter and 60 cm long carrying a mass of 1 kg at its mid-point. The density of the shaft material is 40 Mg/m^3, and Young’s modulus is 200 GN/m^2.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The flywheel of a steam engine has a mass moment of inertia of 2500 Kg-m^2. The starting torque of the steam engine is 1500 N-m and may be assumed constant, using this data find the angular acceleration of the flywheel in rad/s^2.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A disc spinning on its axis at 20 rad/s will undergo precession when a torque 100 N-m is applied about an axis normal to it at an angular speed, if mass moment of inertia of the disc is the 1 kg-m^2

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

An Internal combustion engine has a connecting rod of mass 2 kg and the distance between the centre of crank and centre of gudgeon pin is 25 cm. The Center of Gravity lies at a point 10 cm from the gudgeon pin along the line of centres. The radius of gyration of this system about an axis through the Center of Gravity perpendicular to the plane of rotation is 11 cm. If two masses are used instead of the connecting rod, one at the gudgeon pin and other at the crank pin, if the angular acceleration of the rod is 23 000 rad/s^2, then find the correction couple in N-m.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The flywheel of a machine having weight of 4500 N and radius of gyration of 2 m has cyclic fluctuation of speed from 125 r.p.m to 120 r.p.m. Assuming g = 10m/s^2, the maximum fluctuation of energy is

asked Sep 21, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the mass is of 10 Kg, find the natural frequency in Hz of the free longitudinal vibrations. The displacement is 0.01mm.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The natural frequency (in Hz) of free longitudinal vibrations is equal to

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The ratio of the maximum displacement of the forced vibration to the deflection due to the static force, is known as

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Find the natural frequency in Hz of the free longitudinal vibrations if the displacement is 2mm.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

The accelerometer is used as a transducer to measure earthquake in Richter scale. Its design is based on the principle that

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Calculate the static deflection in µm of transverse vibrations if the frequency is 200Hz.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

...