Isolation factor is twice the transmissibility ratio.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

If isolation factor is negative, then what is the phase difference between transmitted and disturbing force?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the damper is not provided and the system is in resonance, which of the following is the correct isolation factor?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Which of the following is correct regarding isolation factor?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Which of the following is a type of transmitted force to the foundation?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When a periodic disturbing force is applied to a machine, the force is transmitted to the foundation by the means of spring.

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Which of the following is true regarding Ɛ>1?

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Which of the following systems produce a vibration in the foundation?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In vibration isolation system, if ω/ωn < 2, then for all values of damping factor, the transmissibility will be

asked Sep 22, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a three rotor system in the figure given below, the length of one shaft(P) is twice the other(Q), then what is the relation between the Mass moment of inertia of the shafts.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a two rotor system, the mass moment of inertia of one shaft(A) is twice the other(B), then what is the relation between the length of the shafts.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a two rotor system, the length of one shaft(A) is twice the other(B), then what is the relation between the Mass moment of inertia of the shafts.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Increasing which of the following factor would result in increase of free torsional vibration?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

If the pinion has 20 teeth and the gear has 32 teeth, then what is the gear ratio?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Keeping the mass moment of inertia of left end and the right end shafts in a three rotor system same, if the length of one shaft is doubled what should be the effect on the length of other shaft?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a gearing system, the equivalent system is made consisting of three rotors. How many nodes will this new equivalent system will have?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

At a nodal point in the shaft, the frequency of vibration is _________

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

When inertia of gearing is taken into consideration, then an additional shaft must be introduced in the equivalent system of the rotors connected by the shaft.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a gearing system, pump speed is one third of the motor. Shaft from motor is 6 cm in diameter and 30cm long, the impellar shaft is 10cm diameter and 60cm long. Mass moment of inertia is 1500 Kg-m^2, C = 80Gn/m^2. Neglecting the inertia of shaft and gears calculate the frequency of free torsional vibrations in Hz.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

Frequency is independent of the no. of nodes.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

What is the total number of nodes formed in a three rotor system if the rotors at one of the ends and the one in the middle rotate in the same direction?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

In a system with different shaft parameters, the longest shaft is taken for calculations.

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For a gearing system, the equivalent system is made consisting of two rotors. How many nodes will this new equivalent system will have?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

A single cylinder oil engine works with a three rotor system, the shaft length is 2.5m and 70mm in diameter, the middle rotor is at a distance 1.5m from one end. Calculate the free torsional vibration frequency for a two node system in Hz if the mass moment of inertia of rotors in Kg-m^2 are: 0.15, 0.3 and 0.09. C=84 kN/mm^2

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

the given figure, considering left end has one rotor, If the mass moment of inertia of the shaft till node N1 is increased to four times, then what will be the effect on free torsional vibrations of a rotor at left end of N1?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

+1 vote

1 answer

For the free torsional vibration of a geared system which of the following statement is true?

asked Sep 23, 2022 in Machine Dynamics by Grayson (34.3k points)

...