The circumferential hoop stress and longitudinal stress are both shear stress.

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

+1 vote

1 answer

If no re boring allowance is to be given, then thickness of cylinder wall is max pressure is 3.5N/mm², bore diameter=200mm and permissible tensile stress is 40N/mm².

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Petrol engine are more economical than diesel engine.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If diameter of cylinder bore is 120mm, then thickness of water jacket wall will be

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If diameter of cylinder bore is 120mm, then thickness of dry liner will be

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If diameter of cylinder bore is 120mm, then thickness of water cylinder flange will be

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If diameter of cylinder of bore is 120mm, then thickness of the cylinder will be

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Longitudinal stress in a cylinder is given by [symbols have their usual meanings].

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

If circumferential stress is P, then longitudinal stress in the pressure vessel is?

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame’s equation. Diameter of the cylinder is 40mm and pressure in cylinder is 10MPa.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the interference [E=210kN/mm²].

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the radial stresses due to shrink shift in jacket.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². In service the cylinder is further subjected to an internal pressure of 25MPa. Calculate the tangential stress in compound cylinder.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the radial stress due to shrink shift in inner tube.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². In service the cylinder is further subjected to an internal pressure of 25MPa. Calculate the radial stress in compound cylinder.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the shrinkage pressure.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Tangential stress in a cylinder is given by [symbols have their usual meanings].

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Cylinder having inner diameter to wall thickness ratio less than 15 are

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A compound cylinder consists of

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Lame’s equation is generally used for ductile materials.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Autofrettage is beneficial for the high pressure cylinder.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A cylinder is considered thin when the ratio of inner diameter to wall thickness is more than 5.

asked Jan 21 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Lame’s equation used to find the thickness of the cylinder is based on maximum strain failure.

asked Jan 21 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Referring to figure 1, determine the required length of the weld joining two steel plates which are 10mm wide and 10mm thick. The permissible shear stress in the weld is 80N/mm²

asked Jan 27 in Machine Design by Carter (89.5k points)

...