Velocity ratio and transmission ratio are the same thing.

Question

Velocity ratio and transmission ratio are the same thing.

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

Cycloidal teeth consist of

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

In cycloidal gears contact area is

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Pressure angle remains constant in case of involute profile.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Pressure angle is _____ in case of cycloidal teeth.

asked Jan 21 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Hydrostatic and hydrodynamic lubrication are the same thing.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Greater the velocity ratio, smaller the gearbox.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

There is same type of tooth meshing in helical and spur gear.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If centre distance between the two gears on same shaft is unequal to the centre distance on the other two gears on the second shaft, then this gear train is called reverted gear train.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

The direction of tangential component for a driving gear is same to the direction of rotation.

asked Jan 21 in Machine Design by Carter (89.5k points)

0 votes

0 answers

There are ____ standard systems for the shape of gear teeth.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which of the following are true for worm gears?

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The two gears are said to have conjugate motion if

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which of the following are true about epicyclic gear train?

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Which of the following are not true for petroff’s equation?

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The teeth of the helical gears are cut parallel to the shaft axis.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

In angular contact bearings, ____ bearings are required to take thrust load in both directions.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Helical gears mounted on parallel shafts are called crossed helical gears.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Which of the following are true about plasticity?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Which of the following are functions of bearings?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Which of the following facts are true for resilience?

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Which of the following statements are not true?

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A herringbone speed reducer consist of 20 teeth pinion driving a 100 teeth gear. The normal module of gear is 2mm. The face width of each half is 30mm and Lewis factor is 0.4. Calculate the material constant K if surface hardness is 400BHN.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the transverse pressure angle in degrees.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the pitch circle diameter of pinion.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the dedendum circle diameter of the pinion.

asked Feb 2 in Machine Design by Carter (89.5k points)

Chris · Answer 1 · 2026-01-27T14:13:14+0000

Correct answer is (b) False

The best explanation: Transmission ratio is measured between first and last gear.

Velocity ratio and transmission ratio are the same thing.

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories