The two teeth have thickness t₁ and t₂. If backlash of t₁ is greater than that of t₂, than

← Prev Question Next Question →

Please log in or register to answer this question.

Related questions

0 votes

0 answers

Backlash is defined as

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the torque on the gear A.

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Interference is caused by?

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Calculate the tangential component of gear tooth force.

asked Jan 25 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Interference is maximum when the largest pinion is in mesh with the smallest gear.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Undercutting is consider healthy for the tooth as it eliminates undercutting.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Calculate the torque on the gear B.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Calculate the length of the arm C.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The two gears are said to have conjugate motion if

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A pair of spur gears consist of 25 teeth pinion meshing with a 115 teeth gear. The module is 5mm. Calculate the tooth thickness.

asked Jan 22 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

Which of the following have stronger teeth?

asked Jan 22 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A herringbone speed reducer consist of 20 teeth pinion driving a 100 teeth gear. The normal module of gear is 2mm. The face width of each half is 30mm and Lewis factor is 0.4. Calculate the material constant K if surface hardness is 400BHN.

asked Feb 2 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A herringbone speed reducer consist of 20 teeth pinion driving a 100 teeth gear. The normal module of gear is 2mm. The face width of each half is 30mm and Lewis factor is 0.4. If permissible bending stress is 500N/mm², then calculate the beam strength.

asked Jan 23 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A pair of helical gears consist of 25 teeth pinion gear meshing with a 90 teeth gear. Calculate the wear strength If surface hardness is 260BHN. Also face width=35mm, module=4mm and helix angle=25⁰.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

The common normal to the curves of the two teeth must not pass through the pitch point.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of helical gears consist of 25 teeth pinion gear meshing with a 90 teeth gear. Calculate the material constant k If surface hardness is 260BHN.

asked Jan 27 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Among the normal module and transverse module, which one has greater value?

asked Jan 25 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the transverse pressure angle in degrees.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the pitch circle diameter of pinion.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the dedendum circle diameter of the pinion.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate the pitch circle diameter of the gear.

asked Jan 27 in Machine Design by Carter (89.5k points)

+1 vote

1 answer

A pair of parallel helical gears consist of 15 teeth pinion meshing with a 40 teeth gear. The helix angle is 22⁰ and normal pressure angle 19⁰. The normal module is taken as 4mm. Calculate addendum circle diameter of the pinion.

asked Jan 23 in Machine Design by Carter (89.5k points)

0 votes

0 answers

If centre distance between the two gears on same shaft is unequal to the centre distance on the other two gears on the second shaft, then this gear train is called reverted gear train.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

Greater the velocity ratio, smaller the gearbox.

asked Feb 2 in Machine Design by Carter (89.5k points)

0 votes

0 answers

There are ____ standard systems for the shape of gear teeth.

asked Feb 2 in Machine Design by Carter (89.5k points)

...