The working depth of an involute gear is equal to

Question

The working depth of an involute gear is equal to

← Prev Question Next Question →

1 Answer

Related questions

+1 vote

1 answer

A differential gear in an automobile is a

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a clock mechanism, the gear train used to connect minute hand to hour hand, is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a gear train, when the axes of the shafts, over which the gears are mounted, move relative to a fixed axis, is called

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A differential gear in automobilies is used to

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

When the axes of first and last gear are co-axial, then gear train is known as

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a simple gear train, if the number of idle gears is odd, then the motion of driven gear will

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The gear train usually employed in clocks is a

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

For an involute gear, the ratio of base circle radius and pitch circle radius is equal to

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The outside diameter of an involute gear is equal to pitch circle diameter plus

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Twenty degree full depth involute profiled 19-tooth pinion and 37-tooth gear are in mesh. If the module is 5 mm, the centre distance between the gear pair will be

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The minimum number of teeth on the pinion which will mesh with any gear without interference for 20^0 full depth involute teeth will be

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The working depth of a gear is radical distance from the

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

An involute pinion and gear are in mesh. If both have the same size of addendum, then there will be an interference between the

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A worm gear set is designed to have pressure angle of 30^0 which is equal to the helix angle. The efficiency of the worm gear set at an interface friction of 0.05 is

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In a gear having involute teeth, the normal to the involute is a tangent to the

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The centre distance between two meshing involute gears is equal to

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The radial distance from the _______________ to the clearance circle is called working depth.

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Lewis equation for design of involute gear tooth predicts the dynamic load capacity of a cantilever beam of uniform strength.

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Gears having teeth cut on the rotating face plane of the gear and mate with standard involute spur gears are known as

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

A helical gear has the active face width equal to b pitch p and helix angle α. What should be the minimum value of b in order that contact is maintained across the entire active face of the gear?

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The root angle of a bevel gear is equal to

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

Face width of the bevel gear is usually equal to

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The face angle of a bevel gear is equal to

asked Sep 24, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

In full depth 14^0 involute system, the smallest number of teeth in a pinion which meshes with rack without interference is

asked Sep 25, 2022 in Machine Kinematics by Leo (38.0k points)

+1 vote

1 answer

The angle subtended at the centre of a base circle from the origin of an involute to the point of tangency of the generatrix from any point on the same involute is known as

asked Sep 26, 2022 in Machine Kinematics by Leo (38.0k points)

Greg · Answer 1 · 2022-10-21T07:08:22+0000

Correct choice is (d) 2 x addendum

Explanation: Working depth is twice of addendum and whole depth is sum of addendum and dedendum.

The working depth of an involute gear is equal to

Please log in or register to answer this question.

1 Answer

Please log in or register to add a comment.

Related questions

Categories